+
ETC-4
CR2032
1x
1x
1. Changing the battery
Warning: Risk of explosion if the battery is not replaced correctly. Replace only with the same
type or an equivalent type.
2. Select use mode
The Edisio remote control have 2 working modes (by default, mode1):
Mode 1 : 4 channels
Control all in 1 button : On/O , Open/Close, Dimming* +/-,
ON/OFF
ON/OFF
o
ON/OFF
ON/OFF
Mode 2 : 2 channels
Control with 2 buttons : button 1 and 3 to tun on, open or diming + *
button 2 and 4 to turn o , close or dimming – *
ON
OFF
o
OFF
ON
* Keep pushing the button, the brightness starts to increase/ decrease, release to stop.
This option is only available when remote is associated with dimmer module
How to change mode :
Press button 4" and 1 at the same time.
EN
4
The blue LED will ash :
• 1x for mode 1
3. Linking the switch with a Edisio receiver
ETC-4
4-channels remote control
This product is compatible with all Edisio peripherals, and with the Edisio Smart Home
main unit for control through your smartphone.
Using the Edisio hub, you can control your home wherever you are through your
smartphone and also make your remote control compatible with DiO 1.0 peripherals. For
more information visit: www.getdio.com.
Manual
3.1. Linking with light or shutter module or plug
1x
R button
Push one the R button of the Edisio
receiver.
Within 10 seconds, push the «N°1» button
ON/OFF
ON/OFF
of your remote control.
N°1
o
Within 10 seconds, push again the R
...
button of receiver to con rm the link.
Follow the same process to link the "N°2 –
3 - 4" buttons to other receivers.
o
OFF
ON
R
1
+
• 2x for mode 2
R button
R button
Mode 1
Mode 2
Push one the R button of the Edisio
receiver.
R
R
Within 10 seconds, push the «N°1/ON»
button of your remote control.
N°1
Within 10 seconds, push again the R
button of receiver to con rm the link.
R
R
Follow the same process to link the
"N°2/OFF» of the remote control.
N°2
R
R
Follow the same 2 steps for buttons
N°2
«N°3/ON» and "N°4/OFF to link with other
N°3
receiver(s).
N°4
3.2. Delete the link between the switch and Edisio receiver
Push during 5 seconds the R button of the Edisio receiver.
Within 10 seconds, push the button of remote control to remove.
Within 10 seconds, push again the R button of receiver.
4. Technical speci cations
Protocol: 868 by Edisio
Frequency: 868.3 MHz
Transmission range: 150 m (in free eld)
Indoor use (IP40).
Lithium battery: CR2032 3V (included)
Working temperature: -10°C +40°C
Dimensions: 52 x 28 x 12 mm
5. Supplementing your installation
Supplement your installation with Edisio solutions to control your heating, lighting, roller
shutters or garden.
Easy, high-quality, scalable and economical...learn about all of the Edisio solutions at
www.edisio.com
Recycling
In accordance with European WEEE directives (2002/96/EC) and directives concerning accumulators
(2006/66/EC), any electrical or electronic device or accumulator must be collected separately by a local system
specialising in the collection of such waste. Do not dispose of these products with ordinary waste. Check the
regulations in force. The logo shaped like a waste bin indicates that this product must not be disposed of with
household waste in any EU country. To prevent any risk to the environment or human health due to
uncontrolled scrapping, recycle the product in a responsible manner. This will promote the sustainable use of
material resources. To return your used device, use the return and collection systems, or contact the original
dealer. The dealer will recycle it in accordance with regulatory provisions.
Smart Technology declares that the device ETC-4 is conformed with the requirements and provisions of
Directive RED 2014/53/EU.
R
The complete text of the EU declaration of conformity is available at the following Internet address:
www.chacon.be/en/conformity
Hotline
www.ediso.cm/contact-us/
3.2. Eliminar a ligação a um periférico
V1.0 190808
