Important Installation Instruc- Tions - SSS Siedle LEDF 600 Serie Informacion De Producto

Technische Daten LEDF 600-3/...
Betriebsspannung: 20–30 V DC
Betriebsstrom: max. 260 mA
Farbtemperatur: 6000 K
Lichtstärke: 367 cd/klm
Lichtstrom: 164 lm
Schutzart: IP 54
Umgebungstemperatur:
–20 °C bis +55 °C
Abmessungen (mm) B x H x T:
299 x 99 x 50
Technische Daten LEDF 600-4/...
Betriebsspannung: 20–30 V DC
Betriebsstrom: max. 335 mA
Farbtemperatur: 6000 K
Lichtstärke: 486 cd/klm
Lichtstrom: 194 lm
Schutzart: IP 54
Umgebungstemperatur:
–20 °C bis +55 °C
Abmessungen (mm) B x H x T:
399 x 99 x 50
English
Application
LED surface area light for illumina-
tion of info signs or the door station
with energy-saving LEDs.
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Important installation instruc-
tions
The legibility of an inscribed module
is around 400 mm underneath the
LED lighting unit.
Scope of supply
• LEDF 600-... with retaining plate
• Info sign
• 4 sheet metal screws
• 4 clamping claws, short
• 4 clamping claws, long
• 4 plain washers
• 4 wood screws
• 4 dowels
• Locking key
• Clamping block LEDF 600-...
• This product information
Terminal assignment
+, - Supply voltage
20–30 V DC
Installation
1 Plug in the connecting cable at the
terminal block. Note the maximum
admissible range depending on
the number of LEDF 600-... units
being supplied. Specification for
30 V DC, 0.8 mm core diameter e.g.
LNG 600-...
1 LEDF 600-3... max. 480 m
2 LEDF 600-3... max. 240 m
3 LEDF 600-3... max. 160 m
4 LEDF 600-3... max. 120 m
1 LEDF 600-4... max. 370 m
2 LEDF 600-4... max. 185 m
3 LEDF 600-4... max. 125 m
The operating voltage at the
LEDF 600-... must not be lower than
20 V DC.
Flush, surface or free-standing
mounting
2 Using the locking key, between
the LED light unit and the info sign,
push the two locking elements to
the left. Hinge the info sign forwards
and remove from the retaining plate.
3 Depending on the mounting
method, pierce the film on the
retaining plate over the fastening
holes.
4 Insert the terminal block on the
left-hand side of the housing and
connect the supply voltage. When
mounting in a deep housing, the
mounting adapter MA/LEDF 600-...
which is available as an accessory
can be used.
5 When mounting on a flush-
mount housing GU 611-..., use
the provided wood screws. Plug
LEDF 600-... in at the terminal
block. Insert the retaining plate in
the combination frame and screw to
the flush mount housing using the
4 screws. The guiding holes in the
retaining plate and support edge
are designed to ensure a precise
fit. MR 611-..., ISM 611-... and
LEDF 600-... are always mounted
from bottom to top to ensure
that the sealing film lies under the
module carrier of the unit above,
in a similar way to overlapping roof
tiles.
7