AVS Electronics OUTSPIDER PA Manual Del Usuario página 21

Sensor OUTSPIDER PA
The sensors can be connected in DIP/RELE' mode or in PC/BUS mode:
DIP/RELE' Mode (SW2:DIP1-ON):
The programming occurs via the two sets of dip-switches which are on
board:
In this working mode:
- the relay and O.C. outputs are active
- the RS485 derial is not active
- the USB connexction is active
- the HPWIN software only allows the visualization (and not the
programming) of the detector status.
- The connection of the detector occurs exclusively using the
relays and outputs on board.
PC mode and BUS activation (SW2: DIP1-OFF):
E
The programming can occur by PC via the HPWIN software or via the
Dip mode following a special procedure.
N In the PC mode, although previously set in the detector by the DIP-
SWITCH, the configuration can be modified using the HPWIN program.
In this working mode:
G
- The relay and O.C. outputs are active, The RS485 serial is active,
The USB connection is active.
- The HPWIN software allows the entire management of the detector
- The connection of the detector occurs by using the RS485 serial or
the relays on board.
Only management of the LEDs and the AUX clamp cannot be modified through the PC, but only
using the related DIP SWITCHES (1 - 2 - 3 - 4 - 5 - 6 and 8 of the SW 2).
Acquisition sensor OUTSPIDER PA WS 4
Follow the radio sensors acquisition procedure described in either the central stations or receiver
which the sensors will be coupled with.
The detector pairing happen only with a TAMPER alarm transmission; each detector will be associated to the
first free zone in the control panel
Cancellation of the code of the control panel OUTSPIDER PA WS 4
To detach the sensor from the control panel for reuse in another system, it is necessary to
perform the following procedure to delete the control panel code memorised:
- remove and reinsert the sensor battery
- in the first 10 seconds press the TAMPER button 3 times in quick succession
- If the operation is successful, the GREEN LED light will come up steadily for a few seconds
USB-OUT module
Connector for connecting the module mod. USB-OUT (item 1135105) for
SW 1
SW 2
ON
SW1
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
SW2
1.0
1.5
2.2
2.7
MW
GIALLO ROSSO VERDE
USB
the USB connection active, take the USB-OUT module cable from the lower
side of the detector beside the blocking screw of the cover
OUTSPIDER PA WS 4 and OUTSPIDER PA WS (UB) (U)
To connect the sensor to the PC you must enable the USB interface via the
DIP 2 of SW1 in OUTSPIDER PA WS 4 and DIP 6 of SW1 before attaching
the connecting cable between the PC and the sensor.
Once DIP 6 is switched ON, wait about 10 seconds and then connect the
cable to the sensor and the PC.
When the USB interface is activated, the sensor has a constant
consumption of about 35 mA. Once you have finished working with
your PC, disconnect the USB cable and switch the DIP to OFF to
set the sensor in normal operating, low consumption mode.
- 21 -
direct handling of the sensor by way of the PC.
With the USB-OUT adapter it is possible to connect the sensor
directly to the PC for managing through the HPWIN software.
OUTSPIDER PA
In the RELAY mode: through this connection it is possible to
display the configuration made by way of the DIP SWITCH,
display actual sensor operation and acquire the download of
the last 1920 events to the pc.
In BUS mode: through this connection it is possible to display
and modify the configuration, even is
previously completed by way of DIP
SWITCH, adjust microwave
sensitivity, display actual sensor
operation and acquire the
download of the last 1920 events
to the pc.
ATTENTION: in order to test the detector, it is
necessary to close the cover correctly. To maintain