Description Of Symbols; General Safety Warnings - Silverline 580420 Manual De Instrucciones

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Caution!
Toxic fumes or gases!
Risk of fire!
Risk of explosion!
NO open flames!
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
Specification
Maximum operating pressure:..............2.1bar (30psi)
Air Inlet: ................................................¼" BSP, supplied
with two male airline quick connectors (EN-6 'UK' and
EQ-4 'European' types)
Spray gun body material: .....................Polished die cast
Paint container material: ......................Polypropylene (PP)
Paint container volume: ........................100cm
Type of feed:.........................................Gravity
Nozzle diameter: ..................................1.0mm
Fluid output: .........................................70-110ml/min
Min. hose diameters:
8mm ( ⁄ ") for supply hose length up to 15m
5
16
9.5mm (
3
Air consumption: ..................................28-113L/min
Weight: .................................................0.75kg
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
4
aluminium
3
⁄ ") for longer supply hoses
8
(1-4cfm)

General Safety Warnings

• For multiple hazards, read and understand the safety instructions before installing,
operating, repairing, maintaining, changing accessories on, or working near this tool.
Failure to do so can result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of safety measures
and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and markings required by
this part of ISO 11148 are legibly marked on the tool. The employer/user should contact
the manufacturer to obtain replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play
with the appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the tool itself, can
generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool. The grade of
protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
Entanglement Hazards
• Choking, scalping and/or lacerations can occur if loose clothing, personal jewellery, neck
wear, hair or gloves are not kept away from the tool and its accessories
Operating Hazards
• Use of the tool can expose the operator's hands to hazards, including cuts, abrasions
and heat
• Wear suitable gloves to protect hands
• Operators and maintenance personnel should be physically able to handle the bulk,
weight and power of the tool
• Hold the tool correctly; be ready to counteract normal or sudden movements and have
both hands available
• Maintain a balanced body position and secure footing
• Release the start-and-stop device in the case of an interruption of the energy supply
• Use only lubricants recommended by the manufacturer
• Personal protective safety glasses should be used; suitable gloves and protective
clothing are recommended
• Avoid direct contact with moving parts in order to prevent pinching or cutting of hands
or other body parts. Wear suitable gloves to protect hands
• Never run the tool unless it is directed towards the workpiece
• There is a risk of electrostatic discharge if used on plastic and other non-conductive
materials
• Potentially explosive atmospheres can be caused by aerosols and fumes resulting
from spraying
• Always use dust extraction or suppression systems which are suitable for the material
being processed
Repetitive Motions Hazards
• When using this tool to perform work-related activities, the operator can experience
discomfort in the hands, arms, shoulders, neck or other parts of the body
• While using this tool, the operator should adopt a comfortable posture whilst
maintaining secure footing and avoiding awkward or off-balance postures. The operator
should change posture during extended tasks; this can help avoid discomfort and
fatigue
• If the operator experiences symptoms such as persistent or recurring discomfort, pain,
throbbing, aching, tingling, numbness, burning sensations or stiffness, these warning
signs should not be ignored. The operator should inform the employer and consult a
qualified health professional
Accessory Hazards
• Disconnect the tool from the energy supply before filling or changing accessories
• Use only sizes and types of accessories and consumables that are recommended by the
manufacturer of this tool; do not use other types or sizes of accessories or consumables
Workplace Hazards
• Slips, trips and falls are major causes of workplace injury. Be aware of slippery
surfaces caused by use of the tool and also of trip hazards caused by the air line or
hydraulic hose
• This tool is not intended for use in potentially explosive atmospheres and is not
insulated against contact with electric power