Propane Supply; Ventilation; Assembly; Connecting Heater To Cylinder - Pinnacle HeatStream HS-15-TTC Manual De Usuario E Instrucciones De Funcionamiento

NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A FUEL SOURCE
Propane Supply (Continued)
- Be sure that the LP cylinder is located on a level and
stable surface. The burner should be at least 24 inches
from the floor.
- Do not use this heater in a basement or below ground
level. Propane (LP) is heavier than air, and will always
seek the lowest level. If you suspect a leak, shut off the
valve at the LP cylinder immediately.
- Do not use a flame to check for leaks! Use a 50/50
solution of dish soap and water to check for leaks.
Repair any leaks before attempt-ing to re-light the
heater.
- Check the "O" ring on the heater inlet fuel connector for
damage before each use. Replace if damaged or worn.
- Always store the LP cylinder outdoors, but not in an
enclosed area. Never store the LP cylinder near high
heat, direct sunlight or open flames. Never store the LP
cylinder indoors.
- Do not directheater discharge towards any propane
cylinder located within 20 feet of the heater.
- The amount of LP gas used by this heater varies. The
two factors that will determine this are as follows:
1.The amount of gas in the cylinder.
2.The temperature of the cylinder and surrounding area.
Extremely hot during operation. Do
DANGER
not touch any metal components
while in operation. Keep gasoline and any other flam-
mable liquids away from heater. Not for use in resi-
dential living areas or in non-adequately ventilated
enclosed spaces.

Ventilation

For this heater, provide a minimum of 48 square inches of
space by opening a window or door to provide fresh, out-
side air. For additional heaters, provide more ventilation.
Provide at least 3 square feet of opening for ventilation per
100,000 Btu of rated operation.

Assembly

- Tools required: Medium phillips screwdriver
Model HS-30-TTC
1. Place Tank Collar Bracket on top of Center Plate. Be
sure Mounting Bolt Knob is on bottom as shown in
Figure 2.
2. Insert Machine Screw into top hole using Phillips
screwdriver.
4. Insert 2nd Machine screw into bottom hole. This will
secure the Tank Collar Bracket to the Center Plate.
Page 4
Pinnacle Products International, Inc. Tank Top User's Manual
Connecting Heater to LP Cylinder
Be sure to read and understand all of the Safety
Information in this manual before connecting the
heater to the LP cylinder. Installation must conform to
local codes and with the Standard for the Storage and
Handling of Liquefied Petroleum Gases and
ANSI/NFPA 58
Inspect the hose and regulator prior to each use of the
heater. If there is excessive abrasion or wear, or if the
hose is cut, replace it with the proper assembly shown in
the parts list prior to using the heater.
Single Burner Models Only
1. Be sure that the control knob on the regulator is in the
"OFF" position.
2. Line up the threads on the Fuel Connector Nut with the
threads on the LP cylinder valve. Turn Fuel Connector
Nut counterclockwise to tighten. Use a wrench to fully
tighten the nut, being careful not to overtighten.
3. Slowly open the LP cylinder valve.
4. Check all connections for leaks using a 50/50 mixture of
dishsoap and water. Any bubbles appearing show a
leak. Remove and reconnect the Connector Nut to the
valve.
Double Burner Models Only
1. Be sure that the control knob on the regulator is in the
"OFF" position.
2. Line up the slots in the tank collar bracket with the tank
collar ring and slide into place. Be sure the mounting
knob is to the outside, and tighten.
Tip over Switch
Assembly
Swivel
Manifold
Tank Collar Bracket
Figure 2. Perspective view of heater
Propane
Tank Top Heaters
Regulator
Knob
Machine Screws
Fuel Connector Nut
Mounting Bolt Knob