Zwave 26931 Manual De Instrucciones

FCC / IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user's authority to operate the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts de
licence d'Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : 1) cet appareil ne
doit pas occasionner de brouillage préjudiciable et 2) cet appareil doit accepter toutes les interférences
reçues, notamment les interférences qui peuvent provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce
matériel. De telles modifications peuvent annuler le droit de l'utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été définies
afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu résidentiel. Cet
appareil produit, utilise et peut émettre des ondes de fréquence radio et, s'il n'est pas installé et utilisé
conformément aux instructions, il peut provoquer un brouillage préjudiciable aux communications
radio. Il n'existe toutefois aucune garantie que des interférences ne se produiront pas au sein d'une
installation donnée. Si cet appareil occasionne un brouillage préjudiciable à la réception radiophonique
ou télévisuelle, il suffit d'allumer et d'éteindre l'appareil pour déterminer sa responsabilité. Nous
encourageons l'utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des
mesures suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant
l'exposition aux RF, aucune modification apportée à l'antenne ou au dispositif n'est autorisée. Toute
modification apportée à l'antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les
exigences d'exposition aux RF et pourrait annuler le droit de l'utilisateur à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las
especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables
a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1)
este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar toda
interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV
ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones
podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,
de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para
proveer protección razonable contra interferencias perjudiciales en una instalación residencial. Este
equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las
instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no
hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo provoca
interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse encendiendo y
apagando el equipo, se recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de radiofrecuencia
de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio a la antena o
dispositivo podría hacer que el dispositivo supere los requerimientos de exposición de radiofrecuencia
y anular la autoridad del usuario para operar el dispositivo.
FCC — U2ZZW4006 | IC: 6924A-ZW4006
Jasco Products Company | Model: ZW4006 / 26931
CAN ICES-3(B) / NMB-3(B)
Tools you will need
Outils dont vous aurez besoin
Herramientas necesarias
1.
IMPORTANT!
1.
The fixture controlled by the Z-Wave In-Wall Smart Motion Switch
must not exceed 960 watts (Incandescent); 1800W (15A) Resistive or
½ HP Motor. The switch is designed only for use with permanently
installed fixtures.
Getting to know your new Z-Wave device
• Turn ON/OFF manually or remotely via the Z-Wave controller
• Can be included in multiple groups and scenes
• May be used in single-pole installation or with up to two GE-branded
Add-on switches in 3-way or 4-way wiring configurations
• Compatible with all incandescent and CFL/LED bulbs
• Interchangeable button switch — white & light almond buttons in package
• Uses a standard, decorative-size wallplate for single-gang
installations (wallplate not included)
• Blue LED indicates programming confirmation as
well as switch location in a dark room
• Z-Wave Certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for Line (Hot), Load,
Neutral and Ground. Traveler wire required for 3-way or 4-way installation
• The Smart Motion Switch has 3 modes of operation. See Section 4 for more details.
• This Z-Wave device has advanced features that allow you to customize
your experience. These features can be adjusted by a Z-Wave enabled
controller that supports the Z-Wave Configuration command class. For a
complete list of adjustable configurations, visit www.ezzwave.com/config
4.
PROGRAMMING OPTIONS
Many controllers will offer programming changes through the application. Programming changes can also be made directly at the switch through simple button presses.
To program the device manually, refer to the diagram shown above in Section 2 and follow the instructions as displayed below. Programming capabliities vary based on
program and connected device.
Occupancy – Light turns on automatically with motion and off automatically without motion
GUIDE:
Press & hold Flashing LED
Vacancy – Light turns on manually and off automatically without motion
Manual – Light only turns on and off manually
MODE:
Time-out duration – amount of time the
Occupancy
light stays on after motion stops
(DEFAULT)
MODE: TO SET:
Vacancy
5 sec
Manual
1 min
5 min
(DEFAULT)
15 min
MODE:
On
30 min (DEFAULT)
Note: Continue to hold button until LED cycles to flash the Off
correct number of times. Time-out duration does not apply in
manual mode.
Light sensing does not apply in vacancy or manual modes.
5.
Adding your device to a Z-Wave network To exclude and reset the device
1. Follow the instructions for your Z-Wave certified 1. Follow the instructions for your Z-Wave certified
controller to include the smart switch to the controller to exclude a device from the Z-Wave
Z-Wave network. network.
2. Once the controller is ready to include your smart 2. Once the controller is ready to exclude your device,
switch, press and release the top or bottom button press and release the top or bottom button on the
on the smart switch to include it in the network. smart switch to exclude it from the network.
Please reference the controller's manual for
To return to factory defaults
instructions.
Press and release the top button ten times.
Now you have complete control to turn your lamp
Note: This should only be used in the event your
ON/OFF according to groups, scenes, schedules
network's primary controller is missing or otherwise
and interactive automations programmed by your
inoperable.
controller. If your Z-Wave certified controller features
Remote Access, you can now control your lighting
from your mobile devices.
MANUAL • MANUEL •
In-Wall
Smart
Motion Switch
Détecteur de
mouvement
intelligent
à montage mural
Interruptor de pared
inteligente
con sensor de
movimiento
ezzwave.com
Z-Wave ® Certified Wireless Lighting Control
Certifié Z-Wave ® Commande d'éclairage sans fil
Control inalámbrico para iluminación certificado por Z-Wave ®
2.
F. Top Button — Press & release to turn the
switch on
G. Bottom Button — Press & release to turn
the switch off
H. Configuration Button — Changes the
operation mode of switch
A. Ground (Green/Bare)
I. Motion Sensor
B. Load (Black)
J. Blue LED — behind cover
C. Line (Black)
K. Air Gap Switch — Pull the air gap switch
D. Traveler (Red/Other)
out to disconnect the power. Push it all
E. Neutral (White) the way back in for normal operation.
A
B D
H
C E
LIGHT ON WHEN: LIGHTS OFF WHEN: TO SET:
Automatically Automatic
Press & release
Automatic
top button
Press & release Press & release
top button bottom button
Light sensing – motion sensor only turns light on if Motion sensitivity – amount of motion
room is dark required to turn on the light
TO SET: MODE:
High
Medium
(DEFAULT)
Low
6.
To change color of the buttons
This step is optional. Before you start you may want
to change the color of the buttons to match your
wallplate or decor.
DO NOT RETURN THIS
MANUAL
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
If you have any problems or questions, contact our tech support team at
1-800-654-8483, (option 1) Monday–Friday, 7:30am–5pm CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals
and more, visit www.byjasco.com/support.
• No user serviceable parts in this unit.
Si vous avez des problèmes ou des questions, communiquez avec notre
équipe de soutien technique au 1-800-654-8483, option1, du lundi au vendredi,
de 7 h 30 à 17 h (HNC).
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en format
électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro equipo técnico al número:
1-800-654-8483, opción 1 de lunes a viernes, de 7:30 a.m. a 5 p.m., hora estándar del
centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios, manuales
en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-WAVE
DEVICES TO CONTROL APPLIANCES. OPERATION
OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT
ROOM THAN THE CONTROLLED APPLIANCE, ALSO
AN UNINTENTIONAL ACTIVATION MAY OCCUR IF
THE WRONG BUTTON ON THE REMOTE IS PRESSED.
Z-WAVE DEVICES MAY AUTOMATICALLY BE POWERED
ON DUE TO TIMED EVENT PROGRAMMING. DEPENDING
UPON THE APPLIANCE, THESE UNATTENDED OR
UNINTENTIONAL OPERATIONS COULD POSSIBLY
RESULT IN A HAZARDOUS CONDITION. FOR THESE
REASONS, WE RECOMMEND THE FOLLOWING:
DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC
HEATERS OR ANY OTHER APPLIANCES WHICH
MAY PRESENT A HAZARDOUS CONDITION DUE TO
UNATTENDED OR UNINTENTIONAL OR AUTOMATIC
POWER ON CONTROL.
AVERTISSEMENT
RISQUE D'INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
COMMANDE DES APPAREILS:
SOYEZ TRÈS PRUDENT LORSQUE VOUS UTILISEZ LES
DISPOSITIFS Z-WAVE POUR COMMANDER LES APPAREILS.
LE DISPOSITIF Z-WAVE PEUT ÊTRE UTILISÉ DANS UNE
SALLE DIFFÉRENTE DE CELLE DANS LAQUELLE SE TROUVE
L'APPAREIL COMMANDÉ ET UNE ACTIVATION INVOLONTAIRE
PEUT AUSSI SE PRODUIRE SI LE MAUVAIS BOUTON EST
ACTIVÉ SUR LA TÉLÉCOMMANDE. LES DISPOSITIFS Z-WAVE
POURRAIENT ÊTRE ACTIVÉS AUTOMATIQUEMENT À CAUSE
D'UN ÉVÉNEMENT PROGRAMMÉ. SELON L'APPAREIL, CES
UTILISATIONS INVOLONTAIRES ET SANS SUPERVISION
PEUVENT ENGENDRER UN RISQUE. POUR CES RAISONS,
NOUS RECOMMANDONS CE QUI SUIT
N'UTILISEZ PAS LES DISPOSITIFS Z-WAVE POUR
COMMANDER LES RADIATEURS ÉLECTRIQUES OU
D'AUTRES APPAREILS QUI POURRAIENT PRÉSENTER
UN DANGER EN CAS DE COMMANDE D'ACTIVATION
IMPRÉVUE, INVOLONTAIRE OU AUTOMATIQUE.
Scan to view
installation guide
Balayez ce code pour
consulter le guide
d'installation. All brand names shown are trademarks of their
respective owners.
Escanear para ver
Tous les noms de marque illustrés sont des marques
la guía de instalación
de commerce de leurs propriétaires respectifs.
Todas las marcas que aparecen aquí son marcas
26931 registradas de sus respectivos dueños.
ZW4006
3.
F
I
J
G
Removing existing switch
K
Smart Motion Switch
TO SET:
1.
1. Pinch both tabs down to release
button.
2. Lift the button up and off.
3. Put the new button onto the switch
The Jasco Add-on switch is required for Multi-Switch 3-way or
by inserting the tabs near the
4-way installations.
motion sensor first and the tabs on
Connecting the traveler terminal of this switch to a standard, non-
the opposite side second.
GE-branded switch will cause damage or result in improper function.
4. Repeat steps 1 + 2 for the button on
If this switch is a part of a 3-way or 4-way multi-switch installation,
the other side.
do not connect the traveler wire or apply power until GE-branded
Once this step has been completed
Add-on switches are correctly installed. For more information on
please return to section 3.
3-way or 4-way installations, view the manual or quick-start guide
that comes with the GE-branded Add-on switch.
WARRANTY
JASCO Products warrants this product to be free from manufacturing defects for a period of two years
from the original date of consumer purchase. This warranty is limited to the repair or replacement of
this product only and does not extend to consequential or incidental damage to other products that
may be used with this product. This warranty is in lieu of all other warranties, expressed or implied.
Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion
or limitation of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to
state. Please contact Customer Service at 800-654-8483 (option 1) between 7:30AM – 5:00PM CST
or via our website (www.byjasco.com) if the unit should prove defective within the warranty period.
GARANTIE
JASCO Products garantit que ce produit est exempt de tout défaut de fabrication pour une période de
deux ans à compter de la date de l'achat original par l'acheteur. Cette garantie se limite exclusivement
à la réparation ou au remplacement de ce produit et n'est pas applicable aux dommages indirects
ou accessoires survenus sur d'autres produits utilisés avec ce produit. Cette garantie se substitue à
toute autre garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à
la durée d'une garantie implicite ou permettent l'exclusion ou la limitation des dommages indirects
et accessoires; il se peut, par conséquent, que cette garantie ne s'applique pas dans votre cas. Cette
garantie vous confère des droits juridiques précis; vous pouvez jouir d'autres droits qui peuvent varier
d'un État à l'autre. Veuillez communiquer avec le service à la clientèle au 1-800-654-8483 (option 1)
entre 7 h 30 et 17 h (heure normale du Centre) ou par l'intermédiaire de notre site web
(www.byjasco.com) si l'appareil s'avère défaillant au cours de la période de garantie.
GARANTÍA
JASCO Products garantiza que este producto está libre de defectos de fabricación durante un periodo
de dos años a partir de la fecha original de compra por parte del consumidor. Esta garantía se
limita a la reparación o sustitución de este producto solamente y no se extiende a daños derivados
o accidentales causados a otros productos que se usen con esta unidad. Esa garantía remplaza
a todas las demás garantías expresas o implícitas. Algunos estados no autorizan limitaciones en
cuanto a la duración de una garantía implícita ni permiten la exclusión o limitación por daños
accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no apliquen en su caso.
Esta garantía le da a usted derechos específicos, y otros que usted puede tener y que varían según
el estado en el que usted reside. Si la unidad resultare defectuosa dentro del periodo de garantía,
comuníquese por favor con Atención al Cliente en el 800-654-8483 (opción 1) entre 7.30 y 17 h,
ADVERTENCIA
Hora del Centro, o a través de nuestro sitio de internet (www.byjasco.com).
RIESGO DE INCENDIO
JASCO Products Company LLC, Building B
RIESGO DE DESCARGA ELÉCTRICA
10 E. Memorial Rd. Oklahoma City, OK 73114.
RIESGO DE QUEMADURAS
CONTROL DE EQUIPOS ELECTRODOMÉSTICOS:
PROCEDA CON SUMA PRECAUCIÓN AL USAR LOS
DISPOSITIVOS Z-WAVE PARA CONTROLAR EQUIPOS
ELECTRODOMÉSTICOS. EL DISPOSITIVO Z-WAVE
PUEDE FUNCIONAR EN UNA HABITACIÓN DIFERENTE
A LA DEL EQUIPO CONTROLADO. ADEMÁS, PODRÍA
SPECIFICATIONS
PRODUCIRSE UNA ACTIVACIÓN ACCIDENTAL SI SE
OPRIME EL BOTÓN INCORRECTO EN EL CONTROL ZW4006
REMOTO. LOS DISPOSITIVOS Z-WAVE PUEDEN
Power: 120 VAC, 60 Hz.
ENCENDERSE AUTOMÁTICAMENTE DEBIDO A EVENTOS
Signal (Frequency): 908.4/916 MHz.
CRONOMETRADOS PROGRAMADOS. SEGÚN EL
Maximum Loads: 960W, incandescent, ½ HP Motor or 1800W (15A) Resistive
EQUIPO DEL QUE SE TRATE, ESTE FUNCIONAMIENTO
Range: Up to 150 feet line of sight between the Wireless Controller or the closest Z-Wave receiver module.
ACCIDENTAL O SIN SUPERVISIÓN PODRÍA CREAR
UNA SITUACIÓN PELIGROSA. POR TALES MOTIVOS,
Operating Temperature Range: 32-104° F (0-40° C)
RECOMENDAMOS LO SIGUIENTE:
For indoor use only.
NO USAR LOS DISPOSITIVOS Z-WAVE PARA
Specifications subject to change without notice due to continuing product improvement
CONTROLAR CALENTADORES ELÉCTRICOS U OTROS
APARATOS ELECTRODOMÉSTICOS QUE PUDIERAN
SPÉCIFICATIONS
IMPLICAR UN PELIGRO DEBIDO A UN ENCENDIDO SIN
SUPERVISIÓN, ACCIDENTAL O AUTOMÁTICO.
ZW4006
Tension : 120 V c.a., 60 Hz.
Signal (fréquence) : 908,4/916 MHz.
Charges maximales : 960 watts (incandescent), moteur de ½ HP ou résistance de 1800 W (15 A).
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche allant jusqu'à
150 pi.
NOT FOR USE WITH MEDICAL OR LIFE SUPPORT
Plage de températures de fonctionnement : de 32 à 104 °F (de 0 à 40 °C).
EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD NEVER BE USED TO Utilisation intérieure uniquement.
SUPPLY POWER TO, OR CONTROL THE ON/OFF STATUS
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet de changements sans
OF MEDICAL AND/OR LIFE SUPPORT EQUIPMENT.
préavis.
NE PAS UTILISER AVEC UN ÉQUIPEMENT MÉDICAL
ESPECIFICACIONES
OU DE SURVIE
ZW4006
LES DISPOSITIFS COMPATIBLES AVEC LA TECHNOLOGIE
Energía: 120 VCA, 60 Hz.
Z-WAVE NE DEVRAIENT JAMAIS ÊTRE UTILISÉS POUR
Señal (Frecuencia): 908.4/916 MHz.
ALIMENTER OU COMMANDER LA MISE EN MARCHE OU
Cargas máximas: 960 W, incandescente, ½ HP motor o 1800 W (15 A) resistiva
L'ARRÊT DE L'ÉQUIPEMENT MÉDICAL OU DE SURVIE.
Alcance: Hasta 150 pies (45.7m) en línea de visibilidad directa entre el control inalámbrico y el módulo receptor
Z-Wave más cercano.
SE PROHÍBE SU EMPLEO EN EQUIPO MÉDICO
Rango de temperatura de funcionamiento: 32-104 °F (0-40 °C).
O EQUIPO PARA EL MANTENIMIENTO DE LAS
FUNCIONES VITALES Para uso en espacios interiores solamente.
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN USAR
PARA SUMINISTRAR ENERGÍA ELÉCTRICA AL EQUIPO
MÉDICO O AL EQUIPO PARA EL MANTENIMIENTO DE
FUNCIONES VITALES, NI PARA CONTROLAR EL ESTADO
DE ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
GE IS A TRADEMARK OF GENERAL ELECTRIC COMPANY
AND IS UNDER LICENSE BY JASCO PRODUCTS
COMPANY LLC, 10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
© JASCO 2016 | 26931 | ZW4006 | rev. 09/22/16 RT
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service
panel. All wiring connections must be made with the POWER OFF to avoid personal injury
and/or damage to the switch. This device is intended for installation in accordance with the
National Electric Code and local regulations in the United States, or the Canadian Electrical
Code and local regulations in Canada. If you are unsure or uncomfortable about performing
this installation consult a qualified electrician.
Multi-switch wiring
For 3-way installations, please refer to the GE Add-on Switch manual
Single-switch wiring
Before you start, you may wish to change the button color to match your wallplate or decor.
Please proceed to section 6.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the switch; these are marked
A. GROUND — Green/Bare
B. LOAD — Black (connected to lighting)
C. LINE (Hot) — Black (connected to power)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Out to Light (Load)
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Be careful to label
wires according to the previous terminal connection.
B
Single, dual and triple gang boxes
When installing the In-Wall Smart Motion Switch in multiple-gang boxes, it may be
necessary to break off one or both sides of the scored tabs on the front yoke. This does not
D affect the electrical rating of the Smart Motion Switch (see specifications for details).
Observe important wiring information
IMPORTANT! This switch is rated for and intended to only be used with copper wire.
A
E
Wire gauge requirements
C
Use 14 AWG or larger wires suitable for at least 80°C for supplying Line
(HOT), Load, Neutral, Ground and Traveler connections.
From Breaker Box
Wire strip length
For attachment to screw terminals, strip insulation 1" (25mm).
For attachment using the enclosure's holes, strip insulation 5/8" (16mm).
UL specifies that the tightening torque for the screws is 12 lbf-in (14 Kgf-cm).
1. Connect the green or bare copper ground wire to the GROUND terminal.
Out to Light (Load)
2. Connect the black wire that goes to the fixture to the terminal marked LOAD.
3. Connect the black wire that comes from the electrical service
B
panel (Hot) to the terminal marked LINE.
4. Connect the white wire to the NEUTRAL terminal (use included jumper wire if needed).
A
Note: The traveler terminal is only used for 3-way or 4-way wiring and should remain
insulated if the switch is being installed in a 2-way system (one switch & one load).
D
5. Insert Switch into the switch box being careful not to pinch or crush wires.
6. Secure the Switch to the box using the supplied screws.
7. Mount the wallplate.
E 8. Reapply power to the circuit at fuse box or circuit breaker and test the system.
C
Basic operation
The connected light can be turned ON/OFF in the following ways:
Occupancy mode (default)
From Breaker Box
1. The light will turn on automatically when motion is detected
and off when motion is no longer detected.
2. Remotely with a Z-Wave Controller
Vacancy mode
1. The light will turn on by pressing the top button and off
automatically when motion is no longer detected
2. Remotely with a Z-Wave Controller
Manual mode
1. Manually from the front panel of the In-Wall Smart Motion Switch
2. Remotely with a Z-Wave Controller
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with
other Z-Wave certified devices from other manufacturers and/or other
applications. All non-battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the network.
• This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by pressing the On or Off button
• Each Association Group supports 5 total nodes
White (Neutral)
Black
(Load)
Z-Wave
Single
Switch
Green (Ground)
Black (Line / Hot)