Metabo SSE 18 LTX BL Manual Original página 8

Ocultar thumbs Ver también para SSE 18 LTX BL:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

en
ENGLISH
If performance diminishes, recharge the battery
pack.
"Li-Power" li-ion battery packs have a capacity
and signal indicator: (14)
- Press the (13) button, the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removal:
Press the battery pack release (11) button and pull
the battery pack (12) forwards.
Inserting:
Slide in the battery pack (12) until it engages.
5.2
Inserting, removing saw blade
Do not touch the saw blade immediately
following operation of the tool, as it can be
extremely hot and can lead to skin burns.
1 Pull up lever (5) of saw blade quick-clamping
device upwards and hold in this position.
2 Insert the saw blade as far as it will go or remove
it.
3 Release lever (5).
4 Check that the saw blade is securely seated.
5.3
Setting the guide
The cutting depth can be limited by shifting the
guide (2) (e.g. when sawing in front of a wall).
Occasionally shift the guide (2) to achieve even
wear of the saw blade.
1. Swivel the lever (1) downwards and shift the
guide (2) to the desired position. See image
series B
2. Swivel the lever (1) upwards and turn the guide
(2), if needed, until the lever engages again.
Check the guide (2) to ensure that it is securely
fitted. It has to be engaged.
6. Use
6.1
Switching on and off, stroke rate,
Switch-on lock (7):
Trigger (9) locked.
Trigger (9) unlocked.
Switching on, speed: press the trigger switch (9).
The stroke rate can be changed by pressing in the
trigger.
Switching off: Let go of the trigger switch (9) .
Continuous activation: With the trigger (9)
pressed, push in the locking button (8) and
release the trigger. Press and release the trigger
(9) again to switch off.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
8
6.2
Stepless stroke rate setting
The stroke rate can be changed steplessly by
varying the pressure applied to the trigger switch
(9), thus adapting it to the material and working
conditions.
6.3
Working Directions
Sawing:
Use a saw blade geared to the material to be sawn.
Press the machine with the guide (2) against the
workpiece. Switch on the machine, and only then
guide the saw blade against the workpiece.
Do not make contact with any objects or with the
ground with the moving saw blade (danger of recoil
and saw blade fracture!)
Adapt the stroke rate to the material to the sawn.
Avoid excessive pressure on the saw blade
(particularly in the case of long saw blades).
If the saw blade jams, turn the machine off
immediately. Widen the sawn gap slightly with a
suitable tool and take out the machine.
After completing the sawing cut, switch off the
machine and only take it out of the sawn gap to
place it down once the saw blade has come to
a standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials
such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on
the work.
See Fig. B, page 2: The machine is pressed with the
edge of the guide (2) against the workpiece. The
saw blade does not make contact with the
workpiece. Switch on the machine. The corner of
the guide serves as a pivot point around which the
machine is slowly aligned, whereby the saw blade
cuts into the workpiece.
7. Maintenance
On a regular basis, use compressed air to blow out
the machine through the rear ventilation slots.
Regularly clean the saw blade quick-clamping
device (3) and blow out with compressed air. Do not
oil or grease.
8. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Comprehensive range of saw blades for a wide
variety of materials and use cases
B Battery charger: ASC 145 (6.27378), ASC 55
(6.27044)
C Battery packs: 8,0 Ah (6.25369), 5,5 Ah
Tabla de contenido
loading

Tabla de contenido