Matco Tools MT1885 Instrucciones De Operación página 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
This insTrucTion Manual conTains iMporTanT safeTy
inforMaTion.
read This insTrucTion Manual carefully and
undersTand all inforMaTion Before operaTing This
Tool.
Always operate, inspect and maintain this tool in
•
accordance with American National Standards
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face
protection
maintenance on this tool.
• Always wear hearing protection when using this
tool. High sound levels can cause permanent
hearing
recommended by your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
• Air under pressure can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach
tool from air supply before installing, removing or
adjusting
before performing any maintenance on this
tool. Failure to do so could result in injury. Whip hoses can
cause serious injury. Always check for damaged,
OPERATION
Locate center of new hole by using a center punch. Place drill bit tip in
punch mark. Hold drill square with work and start motor. Apply steady,
even pressure. Do not force. Too much pressure can cause bit to break
or overheat. Too little pressure will keep bit from cutting and cause it
to overheat. Reduce pressure just before bit cuts through the work.
When bit has penetrated work and is spinning freely, take it from the
work while the motor is running, then turn off drill. If the drill jams
in the work, release throttle immediately. Disconnect the drill before
removing bit and determining cause of trouble. Do not attempt to free
the bit by starting and stopping the motor.
MT1885
MT1885 1/4" Reversible Mini Air Drill
when operating or
loss. Use hearing protection
any accessory on this
performing
as
tool, or
For FORWARD operation, move the FORWARD/REVERSE lever to the
right side of the trigger. For REVERSE, move the FORWARD/REVERSE
lever to the left side of the trigger. The lever is marked "F" for
FORWARD and "R" for REVERSE.
2
frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Place the tool on the work before starting the tool.
• Slipping, tripping and/or falling while operating
air tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
• Do not carry tool by the hose. Protect the hose
from sharp objects and heat.
• Tool shaft may continue to rotate briefly after
throttle is released Avoid direct contact with
accessories during and after use. Gloves will reduce
the risk of cuts or burns.
• Keep away from rotating end of tool. Do not
wear jewelry or loose clothing. Secure long
hair. Scalping can occur if hair is not kept away
from tool and accessories. Choking can occur
if neckwear is not kept away from tool and
accessories.
• Drill bits can bind suddenly and cause rotation
of the work piece or tool, causing injury to arms
and/or shoulders. Enough torque is generated to
cause falls. Always use sharp bits. Use less down-
ward pressure at breakthrough.
• Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged
labels.
Rev. 07/25/11