Black+Decker BCRTA01 Traducido De Las Instrucciones Originales página 6

ENGLISH
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms along with the date code are shown
:
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Do not stare at operating lamp
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
6
(Original instructions)
Do not attempt to charge damaged batteries.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Forward/reverse slider
3. Bit holder chuck
4. Collar/LED work light
5. Hex key
6. Charging port
7. USB connector
Charging the battery (fig. A)
Insert the USB connector (7a) into the charging port (6).
u
Plug the USB connector (7b) into a USB power supply
u
(not included).
Leave the tool connected to the charger for up to 4 hours.
u
The charging indicator (6a) will illuminate during charging.
u
Once fully charged the charging indicator (6a) will go out.
u
Fitting and removing a Hex key (fig. B, C)
Warning! Make sure the forward reverse slider (2) is in the
locked off position (central position).
Turn the collar (4) anti-clockwise to open the bit holder
u
chuck (3).
insert the hex key (5) into the bit holder chuck (3) until it
u
comes into contact with the magnetic disc (3a) at the end
of the channel, making sure it is central to the chuck body.
Tighten the collar (4) clockwise until the hex key (5) is
u
secure.
A clip on extension collar (3a) is provided to facillitate
u
larger hex keys. Fit as illustrated in figure C.
Warning! Use only with the short end of the hex key sitting in
the slot. Injury may occur if the hex key overhangs the collar
LED work light (fig. D)
The LED work light (4) is activated automatically when the on/
off switch (1) is depressed. The LED will also illuminate when
the trigger is depressed and the forward/reverse slider (2) is in
the locked off position (central position).
Selecting the direction of rotation (fig. E)
For drilling and for tightening hex bolts, use forward rotation.
For loosening hex bolts, use reverse rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the right position.
To select reverse rotation, push the forward/reverse slider
u
(2) to the left position.
To lock the tool, set the forward/reverse slider into the
u
centre position.