Tabla de contenido
18
X-TOUCH
X-TOUCH HUI EMULATION MAP
Rec
Rec
Rec
Rec
Rec
Rec
Solo
Solo
Solo
Solo
Solo
Solo
Mute
Mute
Mute
Mute
Mute
Mute
Select
Select
Select
Select
Select
Select
V-POT Push = automation enable ch
V-POT Assignment
Input
Pan
Out
Send A Send B Send C
RecRdyAll
Window
Automation enable
Rec
Rec
Mix
Edit
Transp
Fader
Mute
Pan
Send
Plug Snd Mute
Solo
Solo
F1
F2
F3
F4
F5
F6
F7
Mute
Mute
Select
Select
Shift
Opt
Read
Write
Trim
Save
Ctrl
Alt
Touch
Latch
Off
Copy
Q Punch
Audition
Loop
In
Out
Online
Bank
<
>
Channel
<
>
<
>
Mode
Using the X-TOUCH with RTP MIDI
The X-TOUCH can be used as an RTP MIDI device over
a Network connection. This is useful in systems where
long USB cables or MIDI cables would otherwise
be required.
The following instructions show the general
preparation of the X-TOUCH for RTP MIDI operation,
and then further details for use with an OS X*
Bypass
network, and a Windows* network.
Preparing the X-TOUCH for RTP MIDI operation
1. On the X-TOUCH, press and hold the SELECT
button of CH1 during power up, to enter the
F8
Settings menu. Observe the text in the scribble-
strip displays.
Undo
2. Turn the 2nd encoder to select NETWORK.
3. The 3rd encoder allows you to select either
Paste
MODE or DHCP:
• MODE selects between using the X-TOUCH as an
Shuttle
RTP SLAVE or an RTP MASTER. In SLAVE mode,
you need to enter the IP address of the X-TOUCH
into your computer's RTP MIDI settings. In
MASTER mode you can enter the IP address of the
Scrub
computer by turning the 3rd encoder one tick to
the right, and use encoders 4-7 to enter the sets
of 3-digits that make up the address. You may use
Port 5004 in both cases, as this is the standard
port for RTP MIDI.
• DHCP can be set to ON or OFF. When DHCP is
set to ON, the X-TOUCH will get its IP address
automatically within the connected network
from the DHCP server. When DHCP is set to OFF,
the IP, Subnet mask, and Gateway have to be
entered manually by turning the 3rd encoder to
the right and accessing the following pages: my
IP, my Mask, and my Gway. You can enter the IP
addresses using encoders 4-7.
4. Exit the X-TOUCH setup by pressing the SELECT
button of CH1 again. You will see the following in
the display: IP: 000.000.000.000
5. The IP will fi rst switch to an internal IP before
it shows the actual IP (for example IP:
010.100.001.029) within the network when DHCP
is used. When the X-TOUCH is connected to the
computer via the network, the Wait message
will disappear.
*OS X is a trademark of Apple Inc.
*Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
Using X-TOUCH as an RTP MIDI
Using X-TOUCH as an RTP MIDI
device within OS X
device with Windows
For OS X systems, no external driver is required for RTP
Windows systems require the use of a third-party
MIDI operation.
external driver for RTP MIDI. For example, do an
internet search for "rtpMIDI" then download and
Slave
install it on your computer.
1. Make sure your computer and the X-TOUCH are
Slave
within the same network.
1. Make sure your computer and the X-TOUCH are
2. Open AUDIO/MIDI-Settings on the computer.
3. Open MIDI Studio / MIDI Devices window.
2. Open the rtpMIDI driver.
4. Double-click on "Network."
3. Click on "+" underneath the DIRECTORY fi eld to
5. Click on "+" underneath the DIRECTORY fi eld
to add a device. Insert Name, the IP of your
X-TOUCH and the port (5004).
4. Create a Session by pressing "+" underneath
6. Create a Session by pressing "+" underneath
the "My Sessions" fi eld and activate the
session created.
5. Activate the X-TOUCH and click "Connect."
7. Activate the X-TOUCH and click "Connect."
6. The X-TOUCH is now available as an RTP MIDI
8. The X-TOUCH is now available as an RTP MIDI
controller. Open the preferences of your DAW
and add it as control surface. Within most DAWs,
Master
it will be detected automatically.
Master
1. Make sure your computer and the X-TOUCH are
1. Make sure your computer and the X-TOUCH are
2. Open the rtpMIDI driver.
within the same network.
3. Create a Session by pressing "+" underneath
2. Open AUDIO/MIDI-Settings on the computer.
3. Open MIDI Studio / MIDI Devices window.
4. Double-click on "Network."
4. For "Who may connect to me:" choose
5. Create a Session by pressing "+" underneath
the "My Sessions" fi eld and activate the
session created.
5. The X-TOUCH is now available as an RTP MIDI
6. For "Who may connect to me:" choose
"Anyone." X-TOUCH should appear as a
participant of the session.
7. The X-TOUCH is now available as an RTP MIDI
controller. Open the preferences of your DAW
Wait...
and add it as control surface. Within most DAWs,
it will be detected automatically.
Quick Start Guide
19
within the same network.
add a device. Insert Name, the IP including port
address (e.g. 10.100.1.29:5004) of your X-TOUCH.
the "My Sessions" fi eld and activate the
session created.
controller. Open the preferences of your DAW
and add it as control surface.
within the same network.
the "My Sessions" fi eld and activate the
session created.
"Anyone." X-TOUCH should appear as a
participant of the session.
controller. Open the preferences of your DAW
and add it as control surface.
Tabla de contenido
