Excessive Foam Production; Programmed Maintenance; Recommended Brushes - ADIATEK ruby 45 light Serie Uso Y Mantenimiento

GB
4. Clean the suction filter.
5. Replace the rubbers if worn out.
6. Check that the suction motor switch is on.
7. Check that the recovery tank is empty.

PROGRAMMED MAINTENANCE

INTERVENTION
RECOVERY TANK CLEANING
SUCTION FILTER CLEANING
SOLUTION TANK FILTER CLEANING
BRUSHES CLEANING
BRUSHES DISASSEMBLY
SQUEEGEE CLEANING
FRONT SQUEEGEE RUBBER REPLACEMENT
REAR SQUEEGEE RUBBER REPLACEMENT
SPLASH GUARD RUBBER REPLACEMENT
SQUEEGEE ADJUSTMENT CHECK
SQUEEGEE HOSE CLEANING
SOLUTION TANK CLEANING
BATTERIES ELECTROLYTE CHECK
BRUSHES MOTOR CHECK
SUCTION MOTOR CHECK
BRUSHES BASE GROUP CHECK
SCREW TIGHTENING

RECOMMENDED BRUSHES

Brushes must be chosen depending on type of floor and dirt to be removed.
The employed material and the bristles diameter are the elements that distinguish different types of brushes.
MATERIAL
PPL (Polypropylene)
NYLON
TYNEX
BRISTLES THICKNESS
PAD HOLDER
MACHINE CODE
ruby 45 light
48901010
48901040
48901050
48901060
48901070
48801010
ruby 55 light
48901110
48901140
48901150
48901160
48901170
48901180
48801020

EXCESSIVE FOAM PRODUCTION

Check that low foam detergent has been used. Even-
tually add small quantities of anti foam liquid into
the recovery tank.
CHARACTERISTICS
Good wear resistance. Maintains characteristics with hot water up to 50°C. It is not hygroscopic.
Excellent wear resistance, even with hot water. It is hygroscopic.
Nylon bristles with grains of abrasive material. Use with caution in order not to mark the floor or ruin the polishing.
Thicker bristles are more rigid and must be used on smooth floor or floor with small joints.
On irregular floors with deep joints or relieves, it is recommended to use softer bristles which penetrate more easily and deeper.
Please be aware that when brushes bristles are worn out and therefore too small, they become rigid and unable to penetrate and
clean deeper. This may also happen with thicker bristles creating brush vibration.
Pad holder is recommended to clean smooth surfaces. It has anchor points which permit the blocking of the abrasive pad during
work.
QUANTITY DESCRIPTION
2 Brush PPL 0,3 Ø 235
2 Brush NYLON 0,5 Ø 235
2 Brush PPL 0,6 Ø 235
2 Brush TYNEX Ø 235
2 Brush 5 mix Ø 235
2 Pad holder Ø 230
2 Brush PPL 0,3 Ø 285
2 Brush NYLON 0,5 Ø 285
2 Brush PPL 0,6 Ø 285
2 Brush TYNEX Ø 285
2 Brush PPL 0,9 Ø 285
2 Brush 5-mix Ø 285
2 Pad holder Ø 280
DAILY WEEKLY
•
•
•
•
•
•
•
•
•
•
•
USE
Irregular floors with large joints.
Smooth floors with small joints and persistent dirt.
Smooth floors with small joints and persistent dirt.
Floors of resistant material and particularly dirty.
For all types of floors.
For pads of 9", for smooth surfaces cleaning.
Irregular floors with large joints.
Smooth floors with small joints and persistent dirt.
Smooth floors with small joints and persistent dirt.
Floors of resistant material and particularly dirty.
Smooth floors with small joints and persistent dirt.
For all types of floors.
For pads of 11", for smooth surfaces cleaning.
22
Please be aware that a bigger quantity of foam is
produced when the floor is not very dirty. In this ca-
se please dilute detergent solution.
TWO-MONTHLY
•
•
•
GB
SIX-MONTHLY
•
•
•