Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Guidance and manufacturer's declaration –electromagnetic emissions
®
®
The WiTouch
and WiTouch
or WiTouch Pro should assure that it is used in such an environment.
®
The WiTouch
and WiTouch
Emissions test
or WiTouch Pro should assure that it is used in such an environment.
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
RF emissions
CISPR 11
RF emissions
Harmonic emissions
CISPR 11
IEC 61000-3-2
Harmonic emissions
Voltage fluctuations /
IEC 61000-3-2
flicker emissions
Voltage fluctuations /
IEC 61000-3-3
flicker emissions
IEC 61000-3-3
Guidance and manufacturer's declaration –electromagnetic immunity
Guidance and manufacturer's declaration –electromagnetic immunity
The WiTouch and WiTouch Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch or
WiTouch Pro should assure that it is used in such an environment.
The WiTouch and WiTouch Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch or
WiTouch Pro should assure that it is used in such an environment.
Immunity test
Immunity test
Electrostatic discharge
(ESD)
Electrostatic discharge
(ESD)
IEC 61000-4-2
IEC 61000-4-2
Electrical fast
transient/burst
Electrical fast
transient/burst
IEC 61000-4-4
IEC 61000-4-4
Surge
Surge
IEC 61000-4-5
IEC 61000-4-5
Voltage dips, short
interruptions and voltage
Voltage dips, short
variations on power supply
interruptions and voltage
input lines IEC 61000-4-11
variations on power supply
input lines IEC 61000-4-11
Power frequency (50/60
Hz) magnetic field IEC
Power frequency (50/60
61000-4-8
Hz) magnetic field IEC
61000-4-8
NOTE U
is the a.c. mains voltage prior to application of the test level.
T
NOTE U
is the a.c. mains voltage prior to application of the test level.
T
Guidance and manufacturer's declaration –electromagnetic emissions
Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
®
Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
Compliance
Compliance
Group 1
Group 1
Class B
Class B
Not applicable
Not applicable
Not applicable
Not applicable
IEC 60601 test level
IEC 60601 test level
±6 kV contact
±6 kV contact
±8 kV air
±8 kV air
±2 kV for power supply lines
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV for input/output lines
±1 kV differential mode
±1 kV differential mode
±2 kV common mode
±2 kV common mode
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 0.5 cycle
T
(>95 % dip in U
)
T
for 0.5 cycle
40 % U
T
(60 % dip in U
)
T
40 % U
for 5 cycles
T
(60 % dip in U
)
T
for 5 cycles
70 % U
T
(30 % dip in U
)
T
70 % U
for 25 cycles
T
(30 % dip in U
)
T
for 25 cycles
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 5 sec
T
(>95 % dip in U
)
T
for 5 sec
3 A / m
3 A / m
Electromagnetic environment – guidance
The WiTouch and WiTouch Pro use RF energy only for its internal
Electromagnetic environment – guidance
function. Therefore, its RF emissions are very low and are not likely to
The WiTouch and WiTouch Pro use RF energy only for its internal
cause any interference in nearby electronic equipment.
function. Therefore, its RF emissions are very low and are not likely to
cause any interference in nearby electronic equipment.
The WiTouch and WiTouch Pro are suitable for use in all establishments
other than domestic and those directly connected to the public low-
The WiTouch and WiTouch Pro are suitable for use in all establishments
voltage power supply network that supplies buildings used for domestic
other than domestic and those directly connected to the public low-
purposes.
voltage power supply network that supplies buildings used for domestic
purposes.
Compliance level
Compliance level
±6 kV contact
±6 kV contact
±8 kV air
±8 kV air
±2 kV for power supply lines
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV for input/output lines
±1 kV differential mode
±1 kV differential mode
±2 kV common mode
±2 kV common mode
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 0.5 cycle
T
(>95 % dip in U
)
T
for 0.5 cycle
40 % U
T
(60 % dip in U
)
T
40 % U
for 5 cycles
T
(60 % dip in U
)
T
for 5 cycles
70 % U
T
(30 % dip in U
)
T
70 % U
for 25 cycles
T
(30 % dip in U
)
T
for 25 cycles
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 5 sec
T
(>95 % dip in U
)
T
for 5 sec
3 A / m
3 A / m
Electromagnetic environment
guidance
Electromagnetic environment
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
Floors should be wood, concrete or
synthetic material, the relative
ceramic tile. If floors are covered with
humidity should be at least 30 %.
synthetic material, the relative
humidity should be at least 30 %.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment.
a typical commercial or hospital
environment.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment.
a typical commercial or hospital
environment.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment. If the user of the
a typical commercial or hospital
[
or
] requires
EQUIPMENT
SYSTEM
environment. If the user of the
continued operation during power
[
or
] requires
mains interruptions, it is
EQUIPMENT
SYSTEM
continued operation during power
recommended that the [
EQUIPMENT
mains interruptions, it is
] be powered from an
SYSTEM
recommended that the [
uninterruptible power supply or a
EQUIPMENT
] be powered from an
battery.
SYSTEM
uninterruptible power supply or a
battery.
Power frequency magnetic fields
should be at levels characteristic of a
Power frequency magnetic fields
typical location in a typical commercial
should be at levels characteristic of a
or hospital environment.
typical location in a typical commercial
or hospital environment.
–
–
or
or
Tabla de contenido
