Troubleshooting Guide - Allmatic BAX900L Manual De Instalación

12. Troubleshooting guide

PROBLEM
1) The green led "power on" does not
lights on.
2) the buttons of the transmitters do not
have any effect on the control unit.
3) Pressing the UP button of the transmit-
ter the automation closes.
4) Pressing the DOWN button of the
transmitter the automation closes.
5) The leds "photo" and "edge" are not lit.
6) The led stop" is turned off.
7) It is not possible to enter into the learn-
ing phase.
7) When a "close" impulse is given the
control unit emits 5 short beeps and does
not move.
Power supply (clamps13, 14)
Absorption
Photocells power supply (clamps 6, 7, 8)
Motor output (clamps 17,18, 19)
Courtesy light output (clamps 15, 16)
Operating temperature
Courtesy light time
Available reception
Maximum range (with tuned aerial and under optimal
conditions)
Number of codes
Recordable transmitters
GUARANTEE - In compliance with legislation, the manufacturer's guarantee is valid from the date stamped on the product and is restricted to the re-
pair or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The
guarantee does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect
product, assembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by environ-
mental interference. The manufacturer's responsibility for damage caused to persons resulting from accidents of any nature caused by our defective
products, are only those responsibilities that come under Italian law.
6-1622605 rev.0 07/05/2013
CAUSES
•
The control unit is not powered.
•
The fuse is damaged.
•
The transmitter has not been learnt.
•
The transmitter is not compliant with the control
unit.
•
The battery of the transmitter is flat.
•
The motor wiring has been performed in a
wrong way.
•
The motor wiring has been performed in a
wrong way.
•
The photocell/ safety edge is under alarm be-
cause of an obstacle.
•
The inputs photo/ safety edge have not been
jumpered.
•
The button used for the stop is a normally open
contact.
•
The input is not jumpered in case the stop
button is not used.
•
The automation is not still.
•
Test photocell/safety edge negative.
•
Test photocell/ safety edge activated without
having installed one photocell/safety edge.
TECHNICAL SPECIFICATIONS BAX900L
230 Vac +15%, -15% ; 50Hz
5W MAX
24 Vdc 3W MAX
230Vac 1000W MAX
230Vac 500W MAX
-10°C ... +55°C
3 minutes
Rolling code a 433.92 MHz
40 - 60 m (433 MHz)
18 billions of billions (ROLLING CODE reception)
1000 (ROLLING CODE )
ITA ENG FRA
•
Check the wiring and power the control unit.
•
Check the functioning of the fuse with a tester and
replace with another one with the same features
(6.3A 250V).
•
Execute the learning of the transmitter (see
chap.6).
•
Check that the transmitter is a B.ro 433Mhz.
•
Replace the battery of the transmitter.
•
Wire again the motor inversing the clamps 18 and
19.
•
Wire again the motor inversing the clamps 18 and
19.
•
Take off the obstacle..
•
Jumper the inputs 2 and 5 if the photocell is not
used. Jumper the inputs 3 and 4 ( starting from the
top) of the molex in case that the photocell is not
used ( see picture pg.1).
•
Check the button type and in case replace it.
•
Jumper the inputs 1 and 2 in case that the stop
button is not used.
•
Give a stop impulse and try again.
•
Check that there are no obstacles in front of the
photocell/safety edge and the correct functioning of
the devices.
Chec that the dip 5 and the dip 6 are set on OFF
•
Check that the connections of the photocells are
correct see Chap. 3 point 8
ESP DEU POR
SOLUTIONS
8 / 8