Memory Deletion; Technical Characteristics - Stobag SRCR 180 A Instrucciones Y Advertencias Para El Instalador

If you need to delete all the data contained in the memory of the
control unit, carry out the following procedure.
The memory can be deleted:
• using a non-memorised transmitter starting from point A;
• using a previously memorised transmitter starting the procedure
from point N.1
Table "A3"

Memory deletion

➨
A Switch the control unit off and activate the ASCENT and DESCENT inputs. Make sure they
remain active until the end of the procedure.
B Power the control unit and wait for the initial beeps.
➨ Press and hold down key ■ of a previously memorized transmitter until you hear a beep
1
(after about 5 seconds) then release it.
Press and hold down key ▲ of the transmitter until you hear 3 beeps;
2
release key ▲ exactly during the third beep.
Press and hold down key ■ of the transmitter until you hear 3 beeps;
3
release key ■ exactly during the third beep.
Press and hold down key ▼ of the transmitter until you hear 3 beeps;
4
release key ▼ exactly during the third beep.
If you wish to delete all the data in the memory, press the ▼ and ▲ keys simultaneously
5
within 2 seconds until you hear the fi rst of 5 beeps, then release them.
N.B. After some seconds, 5 beeps will sound, indicating that all the codes in the memory have been deleted.
4) What to do if...
a short troubleshooting guide!
When the control unit is switched on, you do not hear the
2 beeps and the transmitters or ASCENT and DESCENT
inputs do not control movement.
Make sure the control unit is powered correctly: there must be mains
voltage between terminals 10-11. When the keys are open between
terminals 12-15 and 13-15, the voltage should be measured at ap-
proximately 24 Vdc. Check the integrity of the fuse.
6 beeps will sound after a radio-controlled command.
The radio control is out of synch, the transmitter memorization pro-
cedure must be repeated.

5) Technical characteristics

STOBAG, in order to improve its products, reserves the right to modify their technical characteristics at any time without prior notice. In any
case, the manufacturer guarantees their functionality and fi tness for the intended purposes.
N.B. All technical specifi cations refer to a temperature of 20°C.
Electronic control unit
Power supply
Maximum motor power
Signal voltage (ascent, descent, sensors)
Operating temperature
Dimensions / weight
Protection class
Wind sensor levels (anemometer)
Sun sensor levels
Length of signal cables (ascent, descent, sensors)
Radio receiver
Frequency
Coding
The range of the SKIMY transmitters has been estimated in 200 m in a free area and 35 m inside buildings.
We hereby declare that this device conforms to the fundamental requirements and relevant provisions of the CE directives.
Declaration of conformity: www.stobag.com
www.stobag.com
You can delete:
• the code of the transmitters only, by stopping at point N°4;
• all the data (transmitter codes, TTBUS address, etc.), by carrying
out the procedure through to point 5.
After a radio command, you hear 10 beeps and then the manoeu-
vre starts. The self diagnosis of the parameters in the memory has
detected a fault, a memory deletion must be performed. Control and
repeat the transmitter memorization.
The sensors are installed and there is light or wind, but the
LEDs do not switch on when you rotate the trimmers.
Check the climatic sensors have been connected correctly.
SRCR 180 A
230 Vac 50/60 Hz
1000 W
approx. 24 Vdc
-20÷55 °C
128.5 x 111.5 x 43.5mm / 340g
IP55 (container undamaged)
5÷60 Km/h (con anemometer da 0,4 Hz per Km/h)
5÷60 Klux (with "SKIROSOL SRCK 601" anemometer)
max. 3 m if near other cables, otherwise 100 m.
433.92 MHz
52 Bit rolling code
Example
PP
SRCR 200 A
2x600 W
128.5 x 111.5 x 43.5mm / 400g
5s
GB
17