Tabla de contenido
A34XP & A46XP
Testing
Before you finish the installation, you should perform the following tests to make sure the wiring is
correct and everything is operating properly.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Test Power Wiring
1.
Turn on the receiver, but do not turn up the volume. The amplifier power light should come
on. If not, check the REM and +12V wires.
2.
Turn up the receiver volume slightly. All speakers should operate. If not, check wiring
connections at amplifier and speakers.
Test Speaker Connections
These tests make sure the speakers are connected properly. If speakers don't play at all, one (or
both) speaker wires may be disconnected.
Troubleshooting
Problem
Possible Cause
Amplifier does not operate
No power to +12V terminal
(power LED not on) when
No power to remote wire with
vehicle and radio are on
radio on
Fuse blown
Volume needs to be turned up
Input level control too low
too high for amplifier to work
Radio volume is too sensitive
Input level control too high
Blows fuses
Power wires hooked up
incorrectly
Speakers blown or defective
Engine noise (ignition noise/
Improper ground connections;
static or alternator whine)
ground loop(s)
Protect light comes on, and
Amplifier is in thermal
amplifier shuts down
protection
Faulty speaker connection and/
or crossover
Low battery voltage
Speaker impedance less than
two ohms
No output on channels
Speaker wires not connected to
speakers properly
Input hooked up incorrectly
Corrective Action
Repair wire or connections
Check connections to radio with test light
Check fuse
Adjust input level control to higher setting
Adjust input level control to lower setting
Check power wire connections
Check speakers
Reroute RCA away from main power wires
Reroute RCA cable
Make sure amplifier is grounded to a clean, solid
part of the chassis/frame
Let amplifier cool down before attempting to turn
back on; some installations may require a fan to
keep the amplifier cool, especially if you are
driving subwoofers with the amplifier
Check speakers and/or crossovers for loose or
bad connections
Make sure you are getting between 10.8 and
15.6 volts to the amplifier with a digital multimeter
measured at the amplifier
If you are using four ohm speakers, you cannot
have more than two speakers wired in parallel;
amplifier will not operate into two ohms bridged
Refer to owner's manual for proper installation
procedures
Specifications
AXP Series Two-Channel Amplifiers
Frequency response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz-20kHz, ±0.5 dB
Signal to noise ratio @ rated power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >100 dB
Channel separation @ ref. power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >65 dB, 1 kHz
THD & IMD @ ref. power into 2 ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.8%
Speaker output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 ohms
Input Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 k ohms
Bass boost center frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Hz
Crossover slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 dB/octave, Butterworth
Power requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14.4 VDC (10.8-15.6VDC allowable)
A34XP
Power output @ 14.4 VDC, 20Hz-20 kHz
(4 ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Watts per channel RMS, < 0.5% THD
(2 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Watts per channel RMS, < 0.8% THD
(4 ohms) bridged. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 Watts per channel RMS, < 0.8% THD
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 9/16" x 11 1/8" x 8 7/16" (65mm x 283mm x 214mm)
A46XP
Power output @ 14.4 VDC, 20Hz-20 kHz
(4 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Watts per channel RMS, < 0.5% THD
(2 ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Watts per channel RMS, < 0.8% THD
(4 ohms) bridged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Watts per channel RMS, < 0.8% THD
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 9/16" x 11 1/8" x 8 7/16" (65mm x 283mm x 214mm)
Warranty
Limited One-Year Warranty (USA and Canada)
Length of Warranty: This warranty from Audiovox Electronics Corporation shall be in effect for a period of one year from the date
of the first consumer purchase.
Persons Protected: This warranty will be enforceable by the original owner during the warranty period so long as proof of date of
purchase from an authorized Jensen dealer is presented whenever warranty service is required.
What is Covered: Except as otherwise specified below, this warranty covers all defects in material and workmanship in this product.
The following are not covered: damage resulting from accident, misuse, abuse, neglect, product modification, improper installation,
incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product; damage occurring during
shipment (claims must be presented to the carrier); elimination of car static or other electrical interferences; any product purchased
outside USA or Canada, or on which the serial number has been defaced, modified or removed.
How You Can Get Service:
U.S. Purchasers: Please telephone Jensen at 1-800-323-4815 We will either inform you of the name and address of an authorized
Jensen repair station which will service the product or will advise you to send the product to a factory service center. Canadian
Purchasers: The product should be returned to the Jensen dealer from whom it was purchased and such dealer either will service or
arrange for service of the product. If shipment of the product is required, it should be packed securely. The original dated bill of sale
must always be included with the product as proof of warranty coverage.
What We Will Pay For: We will pay for all labor and material expenses required to repair the product, but you must pay any labor
costs for the removal and/or installation of the product. If the product is shipped for warranty service, you must prepay the initial
shipping charges, but Jensen will pay the return shipping charges if the product is returned to an address inside the USA or Canada.
Exclusion of Certain Damages: THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY IN CONTRACT OR
TORT, WHETHER OR NOT ARISING FROM COMPANY'S NEGLIGENCE, ACTUAL OR IMPUTED. NO PERSON OR
REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR THE COMPANY ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY BE LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states and/or provinces do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state and province to province.
11
Tabla de contenido
