Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Installation
For correct and safe installation, please read these instructions completely.
DANGER
• All Installation work must be performed by an authorized service personnel.
• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.
• Unit not suitable for installations where water jets could be used.
WARNING
• Ensure proper ventilation by maintaining clearance between condenser and wall.
• Never wire compressor directly to electrical supply.
• Warranty is void if Installation is not made in accordance with current Manufacturer's instructions.
Assembly
1. Remove the drip tray from the door and place the grid on top.
2. Snap the drip tray and grid the assembly into the door.
Install Water Bottle
1. Open the dispenser door.
2. Place probe assembly on probe hanger.
3. Place the fresh bottle outside of the cabinet.
4. Remove the entire plastic cap from top of the bottle.
5. Clean the outside of new bottle with a clean cloth.
6. Place the probe into the bottle.
7. Slide the collar down until it clicks in place.
8. Push the head down until the tubes hit the bottom of the bottle.
9. Slide the bottle into the cabinet and close the door.
Connect to Electricity
• Plug the cord into a properly grounded wall outlet. At this moment, the pump will begin to move water from the bottle to the hot and cold tanks. It
will take up to 12 minutes to fill the tanks for the first time. During this period, the pump will run continuously. This is normal.
Activate Heating & Cooling
Notice: This unit will not dispense hot or cold water until the switches are activated. To activate and start the heating and cooling of the water, push
the top side of the power switches in.
• If you do not want to heat the water, push the bottom side of the red switch in.
• If you do not want to cool water, push bottom side of green switch in.
Activate Nightlight
• Push the top side of the blue power switch in to turn the light on. Push the bottom side in to turn the light off.
Dispensing Water
• This unit has been tested and sanitized prior to packing and shipping. During transit, however, dust and odors can accumulate in the tank and lines.
Dispensing cold Water (≤50°F / 10°C)
After setup, it will take up to 1 hour to get water to the maximum cold temperature. During this time, the compressor could run continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control downward to start the flow of cold water.
3. Release the control once the desired fill level is achieved.
Dispensing Hot Water (≥180°F / 82°C)
WARNING:
This unit dispenses water at a temperature that can cause severe burns. Avoid direct contact with hot water. Keep children and pets
away from the unit while dispensing. Never allow children to dispense hot water without proper and direct supervision. Unplug the unit to prevent
unsupervised use by children.
After setup, hot water will be available in 15-20 minutes. (Indicator light will turn off when heating is complete.)
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Slide red button away from you and depress the hot water control downward to start the flow of hot water.
3. Release the control once the desired fill level is achieved.
Changing the Bottle
Caution:
Do not dispense hot, cool or cold water if the red light is flashing, as you could empty the tanks and cause the dispenser to overheat.
A flashing red light on your function lights alerts you when your bottle is empty. Replace the bottle as soon as possible.
1. Open the dispenser door.
2. Slide the empty bottle out of the cabinet.
3. Remove the probe assembly from the empty bottle. Place the probe assembly on the probe hanger.
4. Set the empty bottle aside.
5. Place fresh bottle outside of the cabinet. Remove the entire plastic cap from the top of the bottle. Clean the outside of new bottle with a clean cloth.
6. Place the probe into the bottle. Slide the collar down until it clicks in place. Push the head down until the tubes hit the bottom of the bottle.
1000003362 (Rev. B - 02/16)
Page 10
Tabla de contenido
