Chicco Next2Me Forever Instrucciones De Uso página 19

away from electrical cables and
cords: do not position close to
windows where cords, curtains or
similar could pose a suffocation or
choking hazard. To avoid all risks of
strangulation, never give children
objects with cords or strings at-
tached, or leave them within their
reach.
• When your child is unattended in
the product, always make sure that
the side is raised and locked in
closed position, and aligned
with the upper perimeter of the
product.
• All connectors must be correctly
secured at all times. Check them
regularly and tighten if necessary.
• Newborn babies can suffocate on
soft beds. Avoid placing cushions
or similar objects underneath new-
born babies when they sleep.
FLOOR BED FOR TODDLERS USE
IMPORTANT – READ CAREFULLY
AND KEEP FOR FUTURE REFER-
ENCE.
WARNINGS
• WARNING: The product is in-
tended for use by children over 18
months of age.
• WARNING: To prevent the risk of
fire, do not place the cot near fans,
electric bar fires, gas fires or other
sources of heat.
• Do not leave any small objects
inside the product that might
cause choking or strangulation.
COMPONENTS
A) Legs
A1) Leg with folding foot (x2)
A2) Leg with fixed foot (x2)
B) Upper frame
C) Base
C1) Rear strap fastening buckle (x2)
D) Folding side barrier
D1) Side
D2) Side tilting button
D3) Side removal button (x2)
D4) Safety strap (x2)
E) Mattress
E1) Lower Velcro strap
E2) Upper Velcro strap
E3) Lower mattress
E4) Upper mattress
F) Frame for height adjustment (x2)
F1) Adjustment button
F2) Tubular elements
G) Fastening strap (x2)
G1) Grey cot safety strap fastening buckle
G2) Grey bed fastening and height adjustment prong
H) Fabric
H1) Bed base snap button (x9)
H2) Internal snap button (x2)
H3) External snap button (x2)
H4) Base zipper (x3)
H5) External vertical zipper (x2)
H6) Internal vertical zipper (x2)
FIRST ASSEMBLY
1. Lay the base "C" on the floor (Fig. 1), insert the frame for height
adjustment "F" (Fig. 2) taking care to hold the adjustment buttons
"F1" outwards. Push the tubular elements "F2" all the way down
until you hear a click. Repeat this step on the other side (Fig. 3).
2. Bring the assembled block to point 1 on the folding side barrier
"D", engage the tubular elements "F2" at the top and the rectangu-
lar hooks at the bottom of the barrier "D" (Fig. 4). Insert all four fas-
tening devices until you hear the click that are correctly fastened.
3. Assemble the lower tubular element of leg "A1" by inserting it into
the hole at the base of the leg "A2" (Fig. 5), taking care to keep the
smooth part (without screws) on the same side. You will hear a click
if correctly assembled. Repeat the same step for the other leg.
4. To make it easier to assemble the legs, fold the structure assem-
bled so far on the short side. Making sure that the smooth part
of the legs (without screws) faces outwards, slide the leg tubes
"A" into the lower holes under the base "C" (Fig. 6) and slide them
into the holes of the height adjustment frame "F" (Fig. 7-7A) until
completely locked. Repeat this step with the other leg.
5. Press the adjustment buttons "F1" (Fig. 8) to lower the cot com-
pletely.
6. Insert and slide the upper frame "B" (making sure that the fasten-
ing pins are facing down) into the through-hole of the fabric "H"
(Fig. 9-9A).
7. Assemble the upper frame "B" with fabric in the holes of the
height adjustment frame "F" (Fig. 10) until you hear a locking click
(Fig. 11).
8. Place the fabric on the upper perimeter of the cot (Fig. 12), fasten
all the snap buttons in the bed base "H1" (Fig. 13), close the two in-
ternal vertical zippers "H6" (Fig. 14), and repeat the operation with
the two external vertical zippers "H5" (Fig. 15).
9. Fasten the internal snap buttons "H2" (Fig. 16) and the external
snap buttons "H3" (Fig. 17) to the folding side barrier "D".
10. Close the zippers of the base "H4" (Fig. 18).
11. Place the mattress "E" (Fig. 19).
HEIGHT ADJUSTMENT
12. The product can be adjusted in 11 different heights. To adjust
19