Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTALLATION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
Kenmore folding Wall Sleeve.
If you decide to keep the existing wall sleeve,
you have to redirect the louvers at the back of the
wall sleeve illustration. The use of pliers is
recommended. If you DO NOT redirect, you run
the risk of poor performance or product failure.
This is not covered under the terms of the
Kenmore warranty.
• Pick a location which will allow the conditioned air to
blow into the area you want. Good installation with
special attention to the proper position of the unit will
lessen the chance that service will be needed.
• Assemble the folding sleeve for this unit according to
the instructions provided.
ITEMS IN INSTALLATION
HARDWARE
You may notneed all partsin thekit,Discardunused
_arts
_e
Horizontal
Insulation
Strips
Around Insulation Strips
Support Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
ITEM (inches)
283/4 X 161/2
13/8 X 5/8X 273/16
13/8 X 13/8 x 273/16
13/8 x 3/4x 611/2
13/8 x 13/8 X 611/2
13j4 x 13/8 x 45/16
14 x 41/2 X %
13x
1 X3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
HOW TO INSTALL
a
identify the existing wall sleeve before installing
the unit from the listed below.
Brand
Wall Sleeve Dimensions (inches
Width
Height
Depth
White-WestinghousE
Frigidaire
25-1/2
15-1/4
16, 17-1/2
Carrier (52F series)
or 22
General Electric
iHotpoint
26
15-5/8
16-7/8
Whirlpool
25-7/8
16-1/2
17-1/8
or 23
Fedders/Emerson
27
16-3/4
16-3/4
or 19-3/4
Sears/Kenmore
25-7/8
15-17/32
16-23/32
Emerson/Fedders
26-3/4
15-3/4
15
Carrier (51S Series)
25-3/4
16-7/8
18-5/8
Friedrich
27
16-3/4
16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner,
I_'_ Remove old air conditioner from existing wall
sleeve.
i_
Clean the interior of an existing sleeve.
(Do not disturb seals.)
L_Wall
sleeve must be securely fastened in wall
before installing the air conditioner.
Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
I_
Prepare the wall sleeve for installation of the
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure
A
B
Brand
Sears/Kenmore
White-Westinghouse
Frigidaire Carrier
(52F series)
General Electric
/Hotpoint
Whirlpool
Carrier (51S series)
Fedders/Emerson
Depth(inches
16-23/32
16, 17-1/2
or 22
16-7/8
C
Emerson/Fedders
Friedrich
r_
Install
unit into wall sleeve.
new
CAUTION:
When installation is completed,
replacement
unit MUST have a rearward slope as
shown.
UNIT
Wall Sleeve
17-1/8 or 23
18-6/8
16-3/4
or 19-3/4
15
16-3/4
FRONI_
T-.............
1/4't
U] ............
FIG. 2
-6-
Tabla de contenido
