Manuales relacionados para Rohde & Schwarz Passive Voltage Probe R&S ESH2-Z3
Resumen de contenidos para Rohde & Schwarz Passive Voltage Probe R&S ESH2-Z3
- Página 1 Test and Measurement Division Manual Passive Voltage Probe R&S ESH2-Z3 299.7810.56 Attenuator R&S ESH2Z31 827.6513.06 Printed in the Federal Republic of Germany 1156.6124.32-01...
- Página 2 Dear Customer, R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG. Trade names are trademarks of the owners.
-
Página 3: Safety Instructions
R&S ESH2-Z3 Safety Instructions Safety instructions on the use of Passive Voltage Probe ESH2-Z3 The International Electrotechnical Commission (IEC) for measuring instruments has replaced the IEC348 standard by the more stringent IEC61010-1 standard. Due to this change, we see it necessary to draw your attention again to the following safety-relevant information: 1. -
Página 5: Tabla De Contenido
R&S ESH2-Z3 Contents Contents Safety Instructions Data Sheet Certificate of Quality EU Certificate of Conformity List of R&S Representatives 1 Preparation for Use and Operating Instructions................5 Preparation for Use...........................5 Operating Instructions ........................5 2 Measurement ............................6 Determining the Interference Source Impedance Zs ..............6 Measuring and Evaluating the Interference Level.................6 Practical Effects of the EUT Source Impedance on the measurement results with the Pasive Probe R&S ESH2-Z3 and R&S ESH2Z31..................8... -
Página 7: Grouped Safety Messages
Grouped Safety Messages Make sure to read through and observe the following safety instructions! All plants and locations of the Rohde & Schwarz group of companies make every effort to keep the safety standard of our products up to date and to offer our customers the highest possible degree of safety. Our products and the auxiliary equipment required for them are designed and tested in accordance with the relevant safety standards. -
Página 8: Basic Safety Instructions
Grouped Safety Messages Tags and their meaning DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. - Página 9 Grouped Safety Messages 5. If handling the product yields hazardous of the connecting cable is regarded as the substances or fuels that must be disposed of disconnecting device. In such cases, it must in a special way, e.g. coolants or engine oils be ensured that the power plug is easily that must be replenished regularly, the safety reachable and accessible at all times...
- Página 10 Grouped Safety Messages 20. For permanently installed equipment without national regulations regarding waste built-in fuses, circuit breakers or similar disposal and recycling. protective devices, the supply circuit must be 28. Please be aware that in the event of a fire, fused in such a way that suitable protection toxic substances (gases, liquids etc.) that is provided for users and products.
-
Página 11: Informaciones Elementales De Seguridad
Informaciones elementales de seguridad ¡Es imprescindible leer y observar las siguientes instrucciones e informaciones de seguridad! El principio del grupo de empresas Rohde & Schwarz consiste en tener nuestros productos siempre al día con los estándares de seguridad y de ofrecer a nuestros clientes el máximo grado de seguridad. Nuestros productos y todos los equipos adicionales son siempre fabricados y examinados según las normas de seguridad vigentes. - Página 12 Informaciones elementales de seguridad Tener en cuenta las informaciones de seguridad sirve para tratar de evitar daños y peligros de toda clase. Es necesario de que se lean las siguientes informaciones de seguridad concienzudamente y se tengan en cuenta debidamente antes de la puesta en funcionamiento del producto. También deberán ser tenidas en cuenta las informaciones para la protección de personas que encontrarán en el capítulo correspondiente de la documentación de producto y que también son obligatorias de seguir.
- Página 13 Informaciones elementales de seguridad 3. Como en todo producto de fabricación El empresario/usuario está comprometido a industrial no puede ser excluido en general de valorar y señalar áreas de trabajo en las que que se produzcan al usarlo elementos que se corra un riesgo aumentado de exposición a puedan generar alergias, los llamados radiaciones para evitar riesgos.
- Página 14 Informaciones elementales de seguridad 12. No utilice nunca el producto si está dañado el 20. En caso de que los productos que son cable eléctrico. Compruebe regularmente el instalados fijamente en un lugar sean sin correcto estado de los cables de conexión a protector implementado, autointerruptor o red.
- Página 15 Informaciones elementales de seguridad 27. Baterías y acumuladores no deben de ser de horquilla, carros etc. El usuario es expuestos a temperaturas altas o al fuego. responsable de que los productos sean Guardar baterías y acumuladores fuera del sujetados de forma segura a los medios de alcance de los niños.
- Página 17 R&S ESH2-Z3 Supplement to Data Sheet Supplement to Data Sheet ESH2-Z3 In comparison to data sheet 756.4320.14, the following has changed: Specifications: ± 2 % || 6 pF Input impedance 1.5 k Ordering information: Passive probe ESH2-Z3 0299.7810.56 1156.6124.32...
- Página 19 EC Certificate of Conformity Certificate No.: 2002-15 This is to certify that: Equipment type Stock No. Designation ESH2-Z3 0299.7810.54 /.56 Passive Voltage Probe ESH2-Z31 0827.6513.06 Attenuator complies with the provisions of the Directive of the Council of the European Union on the approximation of the laws of the Member States - relating to electrical equipment for use within defined voltage limits (73/23/EEC revised by 93/68/EEC)
- Página 21 Certified Quality System DIN EN ISO 9001 : 2000 DIN EN 9100 : 2003 DIN EN ISO 14001 : 2004 DQS REG. NO 001954 QM UM QUALITÄTSZERTIFIKAT CERTIFICATE OF QUALITY CERTIFICAT DE QUALITÉ Sehr geehrter Kunde, Dear Customer, Cher Client, Sie haben sich für den Kauf eines you have decided to buy a Rohde &...
-
Página 23: Customer Support
Customer Support Technical support – where and when you need it For quick, expert help with any Rohde & Schwarz equipment, contact one of our Customer Support Centers. A team of highly qualified engineers provides telephone support and will work with you to find a solution to your query on any aspect of the operation, programming or applications of Rohde &... -
Página 25: Address List
Address List Headquarters, Plants and Subsidiaries Locations Worldwide Headquarters Please refer to our homepage: www.rohde-schwarz.com ◆ ROHDE&SCHWARZ GmbH & Co. KG Phone +49 (89) 41 29-0 Sales Locations Mühldorfstraße 15 · D-81671 München Fax +49 (89) 41 29-121 64 ◆ Service Locations P.O.Box 80 14 69 ·... -
Página 27: Preparation For Use And Operating Instructions
R&S ESH2-Z3 Preparation for Use and Operating Instructions 1 Preparation for Use and Operating Instructions Preparation for Use Insert the BNC plug of the Passive Voltage Probe R&S ESH2-Z3 into the RF input socket of the test instrument. When using the an R&S Test Receiver, use the transducer table to enter the values of the voltage division factor and activate the transducer factor. -
Página 28: Measurement
Measurement R&S ESH2-Z3 2 Measurement Determining the Interference Source Impedance Zs Generally, interference sources have low impedance so that measurements using the R&S ESH2-Z3 produce correct results. Though, the levels measured with an undefined source impedance may be incorrect. In order to determine the impedance Zs of the interference source, first measure the level without and then with attenuator 6 at a test frequency complying with CISPR Publication 16-2-1, Section 2.4.6.2 (see Fig. - Página 29 R&S ESH2-Z3 Measurement Test point ESH2-Z3 Measuring M. O. Receiver Ground lead Ground Attenuater ESH2Z31 ESH2-Z3 Measuring M. O. Receiver Fig. 1 Determination of interference source impedance Z s | Zs | / 1000 10000 100000 Measurement error Reduction of indication 1500 Measurement error: 3000...
-
Página 30: Practical Effects Of The Eut Source Impedance On The Measurement Results With The Pasive Probe R&S Esh2-Z3 And R&S Esh2Z31
Measurement R&S ESH2-Z3 Practical Effects of the EUT Source Impedance on the measurement results with the Pasive Probe R&S ESH2-Z3 and R&S ESH2Z31 The test setup in Fehler! Verweisquelle konnte nicht gefunden werden. has been used to show the effects of the EUT source impedance on the measurement results with the Passive Voltage Probe ESH2-Z3 and Attenuator ESH2Z31. -
Página 31: Required Measuring Equipment
R&S ESH2-Z3 Required Measuring Equipment 3 Required Measuring Equipment Item Designation, required specifications Type Order No. Recommended R&S equipment Network analyzer 9 kHz..100 MHz R&S ZVR 1127.8551.61 Calibration kit 2 x BNC measurement cable 2 x BNC connector 0017.6559.00 BNC-T connector 0017.6588.00 Adapter BNC-banana plug 0017.6742.00... -
Página 32: Circuit Description
Circuit Description R&S ESH2-Z3 4 Circuit Description Electrical Function (See circuit diagram 349.7099 S) The Passive Probe is designed to comply with CISPR Publication 16-1-2 in conjunction with IEC 61010- 1 and thus includes a Y-capacitor to decouple it from any AC supply voltages which may be present in the equipment under test.