Troubleshooting Tips - Polk Audio PA D1000.1 Manual De Instrucciones

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13
6. Turn up the level control corresponding to the tweeter output until you hear slight distortion
and turn back the level control slightly for an undistorted output . Depending on your system
the midrange and tweeter output may be on the same output channels .
7. Fine-tune the output level between midrange and tweeters . Refer to the Line Level
Inputs/Outputs/Controls section of this manual for detailed instructions .
8. Repeat Steps 5-7 for the rear speakers . If you do not have rear speakers continue to Step 10 .
9. Set levels between the front and rear midrange and tweeters for optimum front/rear balance .
10. Turn up the level control corresponding to the woofer output until you hear slight distortion
and turn back the level control slightly for an undistorted output .
11. Fine-tune the output level between satellite speakers and the woofers . Refer to the Line Level
Inputs/Outputs/Controls section of this manual for controls . Adjust the level to the bass output
of the woofer to match the sonic requirements of the system .
12. Enjoy your awesome Polk Audio PA D Series amplifier .

TrOuBLESHOOTINg TIPS

Symptom
Probable Cause
No output
Low or no remote turn-on .
Fuse blown .
Power wires not connected .
Audio input not connected .
Speaker wires not connected .
Speakers are blown .
Audio cycles on and off
Thermal protection engages when
amplifier heat sink temperature
exceeds 85° C (185° F) .
Loose or poor audio input .
Loose power connections .
distorted output
Amplifier level sensitivity set
too high exceeding maximum
capability of amplifier .
Impedance load to amplifier too low .
Shorted speaker wires .
Speaker not connected
to amplifier properly .
10
Action To Take
Check remote turn-on at amplifier and repair as needed .
Check power wire's integrity and check for
speaker shorts . Fix as needed and replace fuse .
Check power wire and ground connections
and repair or replace as needed .
Check line level connections and repair
or replace as needed .
Check speaker wires and repair or replace as needed .
Check system with known working speaker
and repair or replace speakers as needed .
Make sure there is proper ventilation for
amplifier and improve ventilation as needed .
Check line level connections and repair
or replace as needed .
Check power wires and ground connections
and repair or replace as needed .
Readjust gain . Refer to the Adjusting the Sound
of the System section of this manual .
Check speaker impedance load if below 1 Ohm,
rewire speakers to achieve higher impedance .
Check speaker wires and repair or replace as needed .
Check speaker wires and repair or replace as needed .
© 2011 Polk Audio—all rights reserved
TrOuBLESHOOTINg TIPS
Symptom
Probable Cause
distorted output
Internal crossover not
set properly for speakers
Speakers are blown
Poor bass response
Speakers wired with wrong polarity
causing cancellation at low frequencies .
Crossover set incorrectly .
Impedance load at amplifier is too low .
Battery fuse blowing
Short in power wire or incorrect wiring .
Fuse used is smaller than recommended .
Actual current exceeds fuse rating .
Amplifier fuse blowing
Fuse used is smaller than recommended .
Impedance load at amplifier is too low .
Speaker is blown with shorted outputs .
Actual current exceeds fuse rating .
© 2011 Polk Audio—all rights reserved
Action To Take
Readjust crossovers . Refer to the Amplifier Settings
section of this manual for detailed instructions .
Check system with known working speakers
and fix or replace as needed .
Check speaker polarity and fix as needed .
Reset crossovers . Refer to the Line Level
Input/Output/Control section of this manual .
Check speaker impedance load if below 1 Ohm,
rewire speakers to achieve higher impedance .
Check power wires and ground connections
and repair or replace as needed .
Replace with proper fuse size .
Check speaker impedance load if below 1 Ohm,
rewire speakers to achieve higher impedance .
Replace with proper fuse size .
Check speaker impedance load if below 1 Ohm,
rewire speakers to achieve higher impedance .
Check system with known working speakers
and fix or replace as needed .
Check speaker impedance load if below 1 Ohm,
rewire speakers to achieve higher impedance .
11
Tabla de contenido
loading

Tabla de contenido