Need help? Call 1.800.694.0013
Do not return to place of purchase.
Installing LP Gas Tank
To operate, you will need one precision-filled standard grill LP gas
tank with external valve threads .
W CAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
grill.
Inserting LP Gas Tank
Place precision-filled LP gas tank upright into the notches in the right cart frame so the tank
valve is facing the gas line connection .
Securing LP Gas Tank
Secure tank by sliding the tank retainer wire over shoulder of LP gas tank .
Connecting LP Gas Tank
1 .
Before connecting, be sure there is no debris caught in the head of the LP gas tank, head
of the regulator valve or in the head of the burner or burner ports .
2 .
Connect regulator/hose assembly to tank by turning knob clockwise until it stops .
Disconnecting LP Gas Tank
1 .
Before disconnecting, make sure the LP gas tank valve
is "CLOSED ."
2 .
Disconnect regulator/hose assembly from LP gas tank
by turning knob counterclockwise until it is loose .
W CAUTION: LP gas tank must be properly
disconnected and removed prior to
moving this grill.
3 .
Place the protective cap cover on the LP tank and
store the tank outdoors in a well ventilated area out of
direct sunlight .
Operating Instructions
Checking for Leaks
20 lb
Burner Connections
9 Kg
1 .
Make sure the regulator hose and valve
connections are securely fastened to the burner
12.2 in. / 31 cm
and the tank .
2 .
Visually check the connection between the
burner/venturi tube and orifice .
3 .
Make sure the burner/venturi tube fits over the
orifice .
W WARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury or damage to property.
4 .
Please refer to diagram for proper installation
(Figure 1) .
5 .
If the burner/venturi tube does not rest flush to the
orifice, as shown, please contact 1 .800 .694 .0013
for assistance .
Tank/Gas Line Connection
1 .
Make 2-3 oz . of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water .
2 .
Make sure control knobs are in the " OFF"
position (Figure 2) .
3 .
Connect LP gas tank per "Installing LP Gas Tank"
section .
4 .
Turn LP gas tank valve to "OPEN ."
5 .
Spoon several drops of solution, or use a squirt
bottle, at all "X" locations (Figures 1 and 3) .
a . If any bubbles appear, turn LP gas tank valve to
"CLOSED," reconnect and re-test .
b . If you continue to see bubbles after several
attempts, turn LP gas tank valve to "CLOSED"
and disconnect LP gas tank, per "Disconnecting
LP Gas Tank" section . Contact 1 .800 .694 .0013
for assistance .
c . If no bubbles appear after one minute, turn
LP gas tank valve to "CLOSED," wipe away
solution and proceed .
Operating Main Burners
First Use
1 .
Make sure all labels, packaging and protective
films have been removed from the grill .
2 .
Remove manufacturing oils before cooking on this
grill for the first time by operating the grill for at
least 15 minutes on (HIGH) with the lid closed .
This will "heat clean" the internal parts and
dissipate odors .
Lighting
W CAUTION: Keep outdoor gas cooking
appliance area clear and free from
combustible materials, gasoline and
other flammable vapors and liquids.
W CAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
W CAUTION: Check and clean burner/venturi tubes for insects and insect
nests. A clogged tube can lead to a fire.
W CAUTION: Attempting to light the burner with the lid closed may cause
an explosion.
1 .
Open lid .
2 .
Check for obstructions of airflow to the burners . Spiders, insects and webs can clog the
burner/venturi tube . A clogged burner tube can lead to a fire .
3 .
All control knobs must be in the " OFF" position (Figure 2) .
4 .
Connect LP gas tank per "Installing LP Gas Tank" section .
5 .
Turn LP gas tank valve to "OPEN ."
6 .
Push and turn control knob to (HIGH) . the burner should light . Repeat up to three times .
7 .
If ignition does not occur in 5 seconds, turn burner control knob " OFF," wait 5 minutes,
and repeat lighting procedure .
8 .
If igniter does not light burner, use a lit match secured with the lighting rod (included with
grill) to light burners . Access the burners through the cooking grid and heat plates . Position
lit match near side of burner (Figure 4) .
Replacement Parts
1.800.694.0013
Figure 1
Burner/
Venturi
Tube
Figure 2
Figure 3
X
X
X
Figure 4
Match
Figure 5
Burner
9
LP Gas Valve
with Orifice
Valve
Soft Pipe
Connection
OFF
APAGADO
X
X
Lighting
Rod
Flame
Slight
Yellow
Slight
Blue
Dark
Blue