Matco Tools Silver Eagle SE135 Guia De Inicio Rapido

Model:
www.matcotools.com
WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
This belt sander is designed to be used to rapidly sand down
materials, to remove rust, paint and welds in hard to reach
areas. Do not use this tool outside of the designed intent.
Never modify the tool for any other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
AIR BELT SANDER 3/4" x 20.5"
SE135
MADE IN TAIWAN
Page 1
Product Type:
AIR BELT SANDER 3/4" x 20.5"
1 YEAR LIMITED WARRANTY
• The manufacturer warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. The manufacturer reserves the right to determine
whether the product failed because of defective material, workmanship or other
causes and to charge back for missing parts. The manufacturer, at its discretion, will
repair products covered under this warranty free of charge. The distributor should
direct the original user to return the product (with the exceptions listed below) with the
distributor's name, address, adequate proof of date of purchase or a copy of warranty
card, and a short note explaining the problem. Failures caused by accident,
alteration, or misuse are not covered by this warranty.
• If one part of this product fails, please do not return the entire product. The
manufacturer will replace free of charge component parts of this product that
fail within 1 year of first use by the original user. Items included in this
category include but are not limited to kits, hand tool kits and any other
product where there are multiple items or components that make up the unit.
Please contact the phone number below in order to obtain the replacement
components covered under warranty.
• The manufacturer or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do not
allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
Unpacking
When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• Simple belt tension lever
• Belt protection guard
• Non-slip handle grip
• Variable speed control
• Increased pulley space for new thicker belts
• Unit comes with:
1 – Sanding Belt 80 Grit – ¾" x 20.5" (20mm x 520mm)
1 – Sanding Belt 100 Grit – ¾" x 20.5" (20mm x 520mm)
SPECIFICATIONS:
Free Speed: 16,000rpm
Size of Belt: ¾" x 20.5" (20mm x 520mm)
Air Consumption: 4cfm
Overall Length: 16.9" (430mm)
Net Weight: 3.08lbs. (1.4kg)
Air Inlet: 1/4"
Air Pressure: 90psi
DO NOT DISCARD – GIVE TO USER