Matco Tools MT2316 Manual De Instrucciones

WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
This sander is designed for sanding metal, plastic and painted
surfaces to strip paint for fine finishes. Do not use this tool
outside of the designed intent. Never modify the tool for any
other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear appropriate
safety equipment and clothing when using this product.
Study, understand and follow all instructions provided with
this product. Failure to read and follow all warnings and
operating instructions may result in damages and serious
injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and By standers).
• Never use this tool for any application other than for which
it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
6" PALM SANDER
3/16" STROKE
MODEL:
MT2316
MADE IN TAIWAN
Page 1
Product Type:
6" PALM SANDER - 3/16" STROKE
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against defective
material or workmanship for a period of 1 year from the date of purchase.
The manufacturer reserves the right to determine whether the part or parts failed
because of defective material, workmanship or other causes. Failures caused by
accident, alteration, or misuse are not covered by this warranty.
The manufacturer, at its discretion, will repair or replace products covered under
this warranty free of charge. Repairs or replacements of products covered under
this warranty are warranted for the remainder of the original warranty period.
The manufacturer or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representa-
tives voids this warranty. The rights under this warranty are limited to the original
user and may not be transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion or limitations of incidental or consequential damages, so
the above limitations may not apply to you.
Authorized Matco Repair Centers:
United States
Matco Air Tool Repair SV
1330 Commerce Drive
Stow, OH 44224
(800) 433-7098
NMG Industrial WTRC
Attn: South Dock
2223 S. Wilson Street
Tempe, AZ 85282
Before Use
When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• Sealed bearings for extended life
• 3/16" (5mm) stroke finish
• Super lightweight (1.5lbs.) and compact for minimum operator fatigue
• Built-in speed regulator
• Low noise and vibration design
SPECIFICATIONS:
Pad Size: 6"
Free Speed: 10,000rpm
Overall Length: 6" (15.24cm)
Net Weight: 1.5lbs. (0.68kg)
Spindle Thread Size: 5/16" x 24
Air Inlet Thread NPT: 1/4" (6mm)
Air Hose I.D. Size: 3/8" (10mm)
Avg. Air Consumption: 5.5cfm
Air Pressure: 90psi
DO NOT DISCARD – GIVE TO USER
Canada
H. T. Pneumatic Rebuilders Inc.
22 Goodmark Place
Units 7 & 8
Toronto, Ontario M9W6R2