Maintenance - JENN-AIR PROSTYLE JDS9860P Guia Del Usuario

M
AINTENANCE
O D
VEN OOR
CAUTION:
• NEVER place excessive weight on or
stand on an open oven door. This
could cause the range to tip over,
break the door, or injure the user.
• NEVER attempt to open or close
door or operate oven until door is
properly replaced.
• NEVER place fingers between hinge
and front oven frame. Hinge arms are
spring mounted. If accidentally hit, the
hinge will slam shut against oven frame
and could injure your fingers.
TO REMOVE:
1. When cool, open the oven door to the
broil stop position (opened about four
inches).
2. Grasp door at each side. Do not use the
door handle to lift door.
3. Lift up evenly until door clears hinge
arms.
TO REPLACE:
1. Grasp door at each side.
2. Align slots in the door with the hinge
arms on the range.
3. Slide the door down onto the hinge arms
until the door is completely seated on the
hinges. Push down on the top corners of
the door to completely seat door on
hinges. Door should not appear crooked.
NOTE: The oven door on a new range may
feel "spongy" when it is closed. This is normal
and will decrease with use.
O W
VEN INDOW
TO PROTECT THE OVEN DOOR
WINDOW:
1. Do not hit the glass with pots, pans,
furniture, toys, or other objects.
2 Do not close the oven door until the oven
racks are in place.
Scratching, hitting, jarring or stressing the
glass may weaken its structure causing an
increased risk of breakage at a later date.
L L
EVELING EGS
• Be sure the anti-tip bracket secures one of
the rear leveling legs to the floor. This
bracket prevents the range from acciden-
tally tipping.
The range should be leveled
when installed. If the range is
not level, turn the plastic level-
ing legs, located at each
corner of the
range, until
range is level.
LEVELING LEG
LEVELING LEG
R R
EMOVING ANGE FOR
C & S
LEANING
1. Shut off gas supply to appliance.
2. Disconnect electrical supply to appliance.
3. Disconnect blower system.
4. Disconnect gas supply tubing to appliance.
5. Slide range forward to disengage from
anti-tip bracket. (See Installation Instruc-
tions for location of bracket.)
6. Reverse procedure to reinstall. If gas line
has been disconnected, check for gas
leaks after reconnection. NOTE: A
qualified servicer should disconnect
and reconnect gas supply.
7. To prevent accidental tipping, range must
be secured to the floor by sliding rear
leveling leg into anti-tip bracket.
21
O
VEN
To assure the proper replacement bulb is
used, order bulb from Maytag Customer
Service. Call 1-800-688-8408, ask for part
number 74004458 - halogen bulb.
CAUTION:
• Disconnect power to range before re-
placing light bulb.
• Allow oven to cool before replacing light
bulb.
• Make sure bulb cover and bulb are cool
before touching.
TO REPLACE OVEN LIGHT BULB:
1. When oven is cool, use fingertips to grasp
edge of bulb cover. Pull out and remove.
2. Carefully remove old bulb by pulling
straight out of ceramic base.
3. To avoid damaging or decreasing the life
of the new bulb, do not touch the bulb
with bare hands or fingers. Hold with a
ANTI-TIP BRACKET
cloth or paper towel. Push new bulb
ANTI-TIP BRACKET
prongs straight into small holes of ce-
ramic base.
4. Replace bulb cover by snapping into place.
ERVICE
5. Reconnect power to the range. Reset
clock.
L
IGHT