Multiplex LS-Stick Instrucciones página 7

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

6.
I
NSTALLATION
6.1 Trainer Stick LED codes
LED code
LED Code 0
LED OFF
LED ON
LED Code 1
1,6 sec
LED Code 2
1,6 sec
LED Code 3
6.2 Installing the Trainer Stick
1. Switch the Teacher transmitter OFF.
2. Plug the Trainer Stick into the Teacher transmitter's
DIN multi-function socket.
Take care to insert the plug the right way round (inden-
tation). Do not forcibly insert the Trainer Stick!
6.3 Binding the Trainer Stick to the Pupil transmitter
The Trainer Stick must be "bound" to the Pupil transmitter
before the system can be used.
! Note:
The trainer model must be left switched off during the
binding process.
1. For the binding process both the Trainer Stick and the
Pupil transmitter must be set to Binding mode.
Carry out the following steps:
Locate the button on the top of the Trainer Stick,
and hold it pressed in with a pointed instrument.
Switch the Teacher transmitter ON.
You can now release the button on the Trainer
Stick:
The LED on the Trainer Stick flashes at a high
rate (LED code 2
Move the Teacher transmitter (still switched on,
with Trainer Stick attached) very close to the Pupil
transmitter.
Switch the Pupil transmitter ON in Binding mode
(see the operating instructions supplied with your
M-LINK transmitter or M-LINK RF module):
The binding process now takes place.
2. When the Pupil transmitter and Trainer Stick are suc-
cessfully bound together, both switch automatically to
normal transmit / receive mode:
The LED on the Trainer Stick flashes steadily at low
rate (LED code 3
! Note: the binding process usually takes just a few
seconds.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions
Wireless Trainer Stick with M-LINK technology
,
FIRST USE
Description
Battery voltage too low
No reception
Binding process in progress
Normal receive operation
6.1).
6.1).
The binding process is required in the following cir-
cumstances:
The first time the Trainer Stick is used.
! Note:
When you first use the Trainer Stick, the binding process
starts automatically - even if you do not press the but-
ton on the top of the stick.
If the frequency range setting on the Pupil transmitter
is changed. For more information on this please refer
to the operating instructions supplied with your trans-
mitter or RF module (see "France mode").
If the Trainer is to be operated in conjunction with a
different M-LINK Pupil transmitter.
6.4 Locating and solving problems with binding
Fault:
The LED on the Trainer Stick flashes at high frequency
even when the binding process has been running for
several seconds.
Cause:
No M-LINK signal of adequate strength detected.
Solution:
Reduce the distance between the Pupil transmitter and
the Trainer Stick.
Ensure that the Pupil transmitter is switched on in
Binding mode.
Repeat the whole binding process.
7.
S
WITCHING THE
ON
OFF
AND
7.1 Sequence for switching ON and OFF
To switch the Trainer system ON, use this procedure:
1. Switch the Teacher transmitter ON with the Trainer
Stick already plugged in:
The LED on the Trainer Stick glows constantly
(LED code 1
6.1).
2. Operate the transfer switch or button on the Teacher
transmitter, and ensure that it controls all the functions
of the trainer model.
3. Switch the Pupil transmitter ON:
The LED on the Trainer Stick flashes slowly and
steadily (LED code 3
The Trainer Stick is picking up an M-LINK signal.
4. Set both the Teacher transmitter and the Pupil trans-
mitter to Trainer mode (see also Chapter
Select those control functions which the Teacher trans-
mitter is to transfer to the Pupil transmitter during
training operations.
You can transfer up to six control functions to the pupil,
i.e. selective training mode is possible (
! Notes:
Consult the operating instructions supplied with
the two transmitters for information on setting the
transmitters to Trainer mode, assigning control
functions, and switching between the Teacher and
T
RAINER SYSTEM
IN NORMAL USE
6.1):
8.).
3.).
Page 2/4
Tabla de contenido
loading

Tabla de contenido