SIOUX SSD10S Serie Instrucciones De Uso Y Lista De Piezas página 3

ADJUSTMENT OF ADJUSTABLE CLUTCH
ABOVE 25 INCH POUNDS
To adjust clutch place adjusting wrench (No. 53099) with pin through opening in the clutch
case. Place 1/4" (6.4 mm) HEX wrench in the Bit Holder, press in and turn until adjusting
wrench falls into the slot of the Nut of the Clutch. Keep Bit Holder depressed in with HEX
Wrench and turn clockwise to increase and counterclockwise to decrease Torque.
BELOW 25 INCH POUNDS CHANGE TO GREEN SPRING NO. 41284
Again place adjusting wrench in position as for the higher Torque, but place a screw driver
blade through the bit holder opening until in contact with the slot at the far end. Rotate screw
driver until adjusting wrench falls into place, again rotate screw driver clockwise to increase
and counterclockwise to decrease Torque.
REVERSE OPERATION
On reversing tools, the direction of spindle rotation is controlled by the reversing button. When the button is depressed, the spindle rotates
counterclockwise. Always depress the button fully to obtain full power. The reversing button on some models can be locked in the reverse
direction by fully depressing and rotating the button clockwise.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an air line filter, pressure regulator,
and lubricator is recommended.
Before connecting to tools, blow out the air line to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8"
(10mm) I.D.
LUBRICATION
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is rec-
ommended.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and
run the tool for 10-20 seconds to distribute oil through the tool.
Lubricate the gears through the grease fitting with Sioux 1232A grease after 100 hours of operation.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil
and run for 10 seconds. This will help remove contaminants and reduce the formation of rust.
SSD10S - Adjustable Clutch
SSD10S - Stall Drive
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
December 1, 2008
Murphy, North Carolina, USA
Date and place of issues
Form ZCE798
Disconnect tool from air supply before performing any adjustment, maintenance, or repair.
SOUND AND VIBRATION READINGS
Catalog No. *Sound Pressure dBA *Sound Power dBA
DECLARATION OF CONFORMITY
SSD10S SERIES
EN 792, EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
Mark S. Pezzoni
Power and Specialty Tools
Name and position of issuer
DEPRESS SPINDLE TO
ENGAGE CLUTCH JAWS
WARNING
80.0 91.6
80.0 91.6
*per PN8NTC1 *per PN8NTC1
98/37/BC.
President
3
ADJUSTING WRENCH
DECREASE
INCREASE
53099
*Vibration m/s
2
3.8
Less than 2.5
*per ISO 8662
Signature of issuer
Date 2013February1/D