Silverline 285873 Manual Del Usuario página 6

285873
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired
c) Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation
Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained
Circular Saw Safety
WARNINGS. Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as that
specified on the nameplate of the tool. A power source with a voltage greater than
that specified for the tool can result in serious injury to the user, and damage to the
tool. If in doubt, do not plug in the tool. Using a power source with a voltage less
than the nameplate rating is harmful to the motor.
• Do not allow anyone under the age of 18 years to operate this saw
• When operating the saw, use safety equipment including safety goggles or
shield, ear protection, dust mask and protective clothing including safety gloves
• Hand-held power tools may produce vibration. Vibration can cause disease.
Gloves may help to maintain good blood circulation in the fingers. Hand-held
tools should not be used for long periods without a break
• Always use recommended blades with correct size and shape of arbor holes
e.g. diamond or round. Blades that do not match the mounting hardware of the
saw will run eccentrically, causing loss of control
• Whenever possible, use a vacuum dust extraction system to control dust/waste
• Power tools must always be held by the insulated gripping surfaces when
performing an operation, ensuring protection if the cutting tool makes contact
with its own cord or hidden wiring. Contact with a 'live' wire will make exposed
metal parts of the power tool 'live' and shock the operator if the insulated
gripping surfaces are not used
• Ensure hands are away from the cutting area and blade. Keep one hand on
auxiliary handle, or motor housing. If both hands are holding the tool they
cannot be cut by the blade
• Do not attempt to cut material thicker than detailed in the Specifications section
of this manual
• Adjust the cutting depth to the thickness of the workpiece i.e. less than a full
tooth of the blade should be visible below the workpiece
• Ensure that work is correctly supported. Large panels may sag under their own
weight and bind the saw blade. Supports must be placed under the panel on
both sides, close to the line of cut and near the edge of the panel
• Ensure all supports and power cables are completely clear of the cutting path
• Always secure the workpiece to a stable platform, ensuring that body exposure
is minimised, avoiding blade binding or loss of control
• For accuracy of cut, and to avoid blade binding, always use a rip fence or
straight edge guide
• Never hold a workpiece in your hand or across your legs whilst cutting
• Always stand to one side when operating the saw
• Be aware that the blade will project from the underside of the workpiece
• Do not reach beneath the workpiece where the guard cannot protect you from
the blade
• Note the direction of rotation of the motor and the blade
• Inspect the workpiece and remove all nails and other embedded objects prior
to starting work
• Do not apply any sideways or twisting force to the blade whilst cutting
• If a cut does not extend to the edge of the workpiece, or if the blade binds in
the cut, allow the blade to come to a complete stop and lift the saw out of the
workpiece
• Do not attempt to free a jammed blade before first disconnecting the machine
from power
• Do not move the saw backwards at any time whilst cutting
• Beware of projected waste. In some situations, waste material may be projected
at speed from the cutting tool. It is the users responsibility to ensure that other
people in the work area are protected from the possibility of projected waste
• If you are interrupted when operating the saw, complete the process and switch
off before diverting your attention
• The blade bolt and washers were specially designed for your saw. For optimum
performance and safety of operation never use damaged or incorrect bolt/
blade washers
• Regularly check the operation of the blade guard. If the guard does not
automatically cover the blade, have the saw repaired before use
• Periodically check that all nuts, bolts and other fixings have not loosened,
tighten where necessary
The tool must be used only for its prescribed purpose. Any use other than those
mentioned in this Manual will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or injury resulting from such
cases of misuse.
The manufacturer shall not be liable for any modifications made to the tool nor for
any damage resulting from such modifications.
Even when the tool is used as prescribed it is not possible to eliminate all residual
risk factors.
Laser Light Safety
The laser system used in this tool does not normally present an optical hazard,
however it is important to follow the safety rules below:
• Do not switch on the laser light until the tool is ready to cut
• Do not direct the laser light towards yourself or other persons
• Do not point the laser at reflective sheet material as the surface could direct the
beam back at the operator or other persons in the vicinity
• Changes to or replacement of the laser light assembly should only be carried
out by the manufacturer or an authorised agent
• Maintain the laser in accordance with the manufacturer's instructions
CAUTION: Failure to follow safety rules may result in flash blindness and/or
hazardous radiation exposure
www.silverlinetools.com
1300W Circular Saw
5