Important Safety Precautions - Sammic XM-12 Manual De Instrucciones

Users Manual
EN
FIGURES DESCRIPTION - PAGE 3
1- Motor block
2- Blender arm
3- Pilot light
4- Adjustment control
5- "On" button
6- Maximum working tilt
7- Maximum depth
8- Blade
9- Lower seal
10- Assembly / Disassembly of the blender arm
11- Assembly / Disassembly of stirrers
USERS MANUAL
This manual describes the installation, operation and maintenance of the
XM-12, XM-21, XM-22, MB-21, B-20 and MM-20 blenders.
Each machine is identified as follows:
· Name and address of manufacturer: SAMMIC S.L. C/ Basarte 1 -
20720 Azkoitia Gipuzkoa (SPAIN).
· Machine model and serial number.
· Approval marks.
· The serial number and all information regarding the current legislation
under which this appliance has been manufactured is printed on the
guarantee card and in the declaration of conformity.

IMPORTANT SAFETY PRECAUTIONS

In order to reduce the possibility of accidents
(short circuits, injuries or fires, etc.), to get the best
performances from the machine and to maintain
it correctly, read and follow these instructions
attentively. Keep the instructions and make sure that
all users of the machine read them before using it.
Also keep the guarantee card and the declaration of
conformity.
• This appliance has sharpened blades (8). Never
touch the blade when it is moving. Handling
should be limited to cleaning and with the machine
unplugged.
• Before using the machine for the first time, and
always with the machine unplugged, clean the
area in contact with food with (lukewarm) soapy
water, rinse and leave to dry.
• Before plugging the appliance in, make sure
that the mains voltage coincides with the voltage
indicated on the name plate attached to the
machine. Do not plug the appliance in if the arm is
not inside the container that you are working with.
• Never operate the machine empty, outside of a
container. The arm should be submerged up to a
maximum of 2/3 of its length, marked as "MAX" (7).
Never exceed this mark. The maximum working tilt
should be 30° (6).
• The appliance has a pilot light (3) and when said light
is on, this means that it is connected. Handle the
appliance carefully whenever the pilot light is on, as
it will start operating if the "On" button (5) is pressed.
• To avoid splashes, always work with a stable
container and submerge the arm into the container
before starting and do not remove it until it has fully
stopped moving.
• Under no circumstances should the appliance be
operated on a surface with an inclination of over
10 degrees with respect to the horizontal plane.
The machine must always be firmly resting on the
surface. The motor shaft of the machine must always
be in a vertical position in relation to the surface.
• Never place your hand or any other utensil into the
container where the appliance is working in order
to avoid personal or material damage.
• Always disconnect the machine before removing
the blender arm and also before undertaking any
cleaning, inspection or repair work on the appliance.
• Clean the blender arm after each use as described
below. During each operation, check the status
of the lower seal (9). If you see any signs of
deterioration, contact the authorised repair service.
• Avoid water entering the motor block and, under no
circumstances, submerge it in water. If this occurs,
follow these exact instructions:
- Leave the blender inside the container and do not
touch the container.
- Unplug from the mains.
- Remove the appliance from the container and try to
remove as much liquid as possible from inside it.
- Do not connect the machine again and contact an
authorised technical service.
• IMPORTANT: Do not clean the inside or the
outside of the machine with a direct water jet or a
pressurised hose.
• Do not use the machine when the cable, the plug
or the casing are damaged. For repair, contact the
authorised technical service.
• Do not use abrasive detergents (bleach, nitric
acid...) or stainless steel scourers or scrubbers
when cleaning the machine. They may cause rust
or the deterioration of materials.
• Do not allow the appliance to be used as a toy.
This machine is not designed for use by people
(including children of 8 years old and up) with
reduced physical, sensory or mental capabilities
or those lacking the necessary experience or
knowledge, unless they have received supervision
or instructions regarding the use of the appliance
from someone responsible for their safety and
understand the risks that this implies. Do not allow
8
- 8 -