Troubleshooting; Maintaining; Care And Handling Of Discs - Insignia NS-UPDVD Guia Del Usuario

Menu Available options
SPEAKER DOWNMIX–Select how the player downmixes
multi-channel audio to stereo output:
SETUP
• LT/RT–2-channel output, main channel
with surround.
• STEREO–2-channel output, main right
channel with right surround and main
left channel with left surround.
OP MODE–Select according to the TV sound
level:
• LINE OUT–For most systems, this is
the correct setting.
• RF REMOD–If the sound level is too
low when connected directly to the TV,
choose this setting.
DIGITAL
DYNAMIC RANGE–Choose the range between
SETUP
the loudest and softest sounds. This setting is
only available when OP MODE is set to LINE
OUT.
DUAL MONO–Choose the audio output mode.
STEREO is for normal playback and MONO L,
MONO R, and MIX MONO are for karaoke
playback.

Troubleshooting

Use the following check list for troubleshooting
when you have problems with your player.
Consult your local dealer or service outlet if
problems persist. Make sure that all connections
are correctly made when using with other
devices.
Problem Cause
No power The power cord is
disconnected.
The power is turned
off.
Abnormal or The TV is not set to
no picture receive player signal
output.
The video cable is not
connected securely.
The connected TV is
not turned on.
No sound The equipment
connected with the
audio cable is not set
to receive player
signal output.
The audio cables are
not connected
securely.
The power on the
equipment connected
with the audio cable
is turned off.
The audio connecting
cord is damaged.
Poor The disc is dirty.
playback
picture
12
Solution
Plug the power cord into the
power outlet securely.
Press the POWER button to
turn the player on.
Select the appropriate video
input mode on the TV so the
picture from your player
appears on the TV screen.
Connect the video cable to
the jacks securely.
Turn on the TV.
Select the correct input mode
of the audio receiver so you
can listen to the sound from
your player.
Connect the audio cable to
the jacks securely.
Turn on the equipment
connected with the audio
cable.
Replace the cord with a new
one.
Clean the disc.
www.insignia-products.com
Insignia NS-UPDVD 1080p Upconvert DVD Player
The player No disc is inserted.
does not
start
playback
An unplayable disc is
inserted.
The disc is placed
upside down.
The disc is not placed
within the guide.
The disc is dirty.
The rating level is set. Cancel the Rating function or
The remote There is an obstacle
control does in the path of the
not work remote control and
correctly your player.
The batteries in the
remote control are
exhausted.
The remote control is
not pointed at the
remote sensor of
your player.
The remote control is
too far from your
player.
Error WRONG REGIONAL
message on DISC
the screen
WRONG
PASSWORD:
WRONG DISC:

Maintaining

Care and handling of discs

Handling discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on
the disc.
Storing discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Insert a disc (make sure that
the disc indicator in the
display window is lit).
Insert a playable disc. Check
disc type and regional code.
Place the disc with the
playback side down.
Place the disc on the disc tray
correctly inside the guide.
Clean the disc.
change the rating level.
Remove the obstacle.
Replace the batteries with
new ones.
Point the remote control at
the remote sensor of your
player.
Operate the remote control
within 20 ft (6 m).
Disc's region code does not
match the player.
Either the disc's rating is
higher than the player's
rating setting, or you entered
the wrong password in the
SETUP menu.
The player is equipped with
automatic disc quality
detection software. When the
player detects a problem disc
or a damaged disc, the player
may keep playing the disc at
lower quality or stop playing.