Grease filter
Fig. 2
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter B, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 3
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged. Remove the filter holder frame by turning the knobs
(g) 90° that affix the chimney to the cooker hood.
Insert the pad (i) of activated carbon into the frame (h) and fit
the whole back into its housing (j).
It is possible to use a traditional carbon filter,
washable nor regenerable, to be replaced every 3 - 4 months.
The filter holder frame of the carbon filter is welded together;
the eventual frame supplied with the hood is not, therefore, to
be used. Insert it into its housing and fix it turning the 2 plastic
knobs.
Replacing lamps
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
For models shown in Fig. 1E + Fig. 4E:
1. Press on the lamp cover and release to open.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1N/O + Fig. 4N/O:
1. Unscrew the lamp cover.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Refit the lamp cover.
For models shown in Fig.1+Fig.4 (A / B / C / D / F / H / I / K
/ P / Q / S / T / U / V):
1. Extract the lamp cover by levering it off with a small
screwdriver or similar tool.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1J + Fig. 4J:
1. Use a small screwdriver as a lever on the borders of the
lamp in order to remove the lightbulb.
2. Unthread the connector „a".
3. Slide out the lightbulb to be replaced and replace with a
new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD
LINE code 425409.
4. Carry out the replacement and mount the new lightbulb by
following instructions in the reverse.
For models shown in Fig. 1G + Fig. 5G:
Dismount the chimneys: remove the two screws (20 a)
that attaches the upper chimney to the support „G" (Fig.
16).
Remove the box „q": remove the screw „r" that secures
the cooker hood.
Remove the lamp housing „s": remove the screws „t"
that position the housing in the lamp housing area.
Extract the damaged lamp.
Use only PHILIPS type 14515 (GX 5.3) 12V - 75W
halogen bulbs..
Reposition and secure the lamp housing „s" and the box
„q" and remount the chimneys.
For models shown in Fig. 1K + Fig. 4K:
Certain versions of this cooker hood provide for an
incandescent lamp at 40W maximum (E14), remove the
lamp cover to access the lamp housing and carry out any
replacements.
Only for the illustrated model in Fig. 1L + Fig. 6L:
neither
1. Open the front panel "v" upwards, which holds the lamp in
place, ensuring to hold the lamp "z" with one hand.
2. Replace the damaged lamp with one of identical technical
characteristics.
Attention! To guarantee the equivalent quality of lighting,
it is recommended to use the same type of lamp bulb:
Philips neon Lamp bulb 13W Code Ref. 8711500644305.
Ensure that the transparent part of the lamp bulb is facing
inwards so as to guarantee correct light distribution.
3. Replacing the starter:
Use a starter with identical technical characteristics.
Recommended starter: Use a Philips S10 starter.
4. Remount the lamp housing and the front panel in the
inverse in relation to the dismounting.
Only for the models illustrated in Fig. 1M + Fig. 7M:
1. Remove the grease filters.
2. Remove the ceiling light unscrewing the 3 screws that fix it
to the hood (hold the ceiling light to prevent it falling).
3. Change the damaged bulb with one with identical
technical characteristics.
Changing the starter
Use a starter with identical technical characteristics.
Starter advised: use a Phillips S10 starter.
4. Remount the ceiling light and the grease filters in the
reverse manner to the montage.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
22