Victron energy BlueSolar MPPT 75/15 Manual De Instrucciones

Victron energy BlueSolar MPPT 75/15 Manual De Instrucciones

Ocultar thumbs Ver también para BlueSolar MPPT 75/15:
Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

BlueSolar charge controllers MPPT – Overview
Solar charge controller
MPPT 75/15
Maximum Power Point Tracking
Upper
curve:
Output current (I) of a solar panel as function
of output voltage (V).
The maximum power point (MPP) is the point
Pmax along the curve where the product I x V
reaches its peak.
Lower curve:
Output power P = I x V as function of output
voltage.
When using a PWM (not MPPT) controller the
output voltage of the solar panel will be
nearly equal to the voltage of the battery, and
will be lower than Vmp.
Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands
General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40
E-mail: [email protected] | www.victronenergy.com
Feature highlights
Ultra-fast Maximum Power Point Tracking (MPPT)
Advanced Maximum Power Point Detection in case of partial shading conditions
Load output on the small models
BatteryLife: intelligent battery management by load shedding
Automatic battery voltage recognition
Flexible charge algorithm
Over-temperature protection and power de-rating when temperature is high.
Color Control GX
All Victron Energy MPPT Charge Controllers are compatible with the Color Control GX: The Color
Control GX provides intuitive control and monitoring for all products connected to it. The list of
Victron products that can be connected is endless: Inverters, Multi's, Quattro's, MPPT 150/70, BMV-
600 series, BMV-700 series, Skylla-i, Lynx Ion and even more.
VRM Online Portal
Besides monitoring and controlling products on the Color Control GX, the information is also
forwarded to our free remote monitoring website: the VRM Online Portal. To get an impression of the
VRM Online Portal, visit https://vrm.victronenergy.com, and use the 'Take a look inside' button. The
portal is free of charge.
Related product: EasySolar
Minimal wiring and an all-in-one solution: the EasySolar takes power solutions one stage further, by
combining an Ultra-fast BlueSolar charge controller (MPPT), an inverter/charger and AC distribution
in one enclosure.
Model
Load output
Fan
75/15
Yes
No
100/15
Yes
No
100/30
No
No
75/50
No
No
100/50
No
No
150/35
No
No
150/70
No
No
150/85
No
Yes
Battery voltage
Display
Color Control GX
12/24
No
Compatible
12/24
No
Compatible
12/24
No
Compatible
12/24
No
Compatible
12/24
No
Compatible
12/24/36/48
No
Compatible
12/24/36/48
Yes
Compatible
12/24/36/48
Yes
Compatible
www.victronenergy.com
Com. port
VE.Direct
VE.Direct
VE.Direct
VE.Direct
VE.Direct
VE.Direct
VE.Can
VE.Can
Tabla de contenido
loading

Resumen de contenidos para Victron energy BlueSolar MPPT 75/15

  • Página 41: Descripción General

    1 Descripción General 1.1 Seguimiento MPPT ultrarrápido Especialmente con cielos nubosos, cuando la intensidad de la luz cambia continuamente, un controlador MPPT rápido mejorará la recogida de energía hasta en un 30%, en comparación con los controladores de carga PWM, y hasta en un 10% en comparación con controladores MPPT más lentos.
  • Página 42: Fase De Absorción

    1.6 Reconocimiento automático de la tensión de la batería El MPPT 75/15 se ajusta automaticamente a sistemas de 12 ó 24 V. 1.7 Carga en tres fases El controlador de carga MPPT BlueSolar está configurado para llevar a cabo procesos de carga en tres fases: Inicial - Absorción - Flotación 1.7.1.
  • Página 43: Instrucciones De Seguridad

    2 Instrucciones de seguridad Peligro de explosión por chispas Peligro de descarga eléctrica Se aconseja leer este manual detenidamente antes de instalar y utilizar el producto. Este producto ha sido diseñado y comprobado de acuerdo con los estándares internacionales. El equipo debe utilizarse exclusivamente para la aplicación prevista. Instale el producto en un lugar protegido del calor.
  • Página 44: Instalación

    3. Instalación 3,1. General ● Montar verticalmente sobre una superficie no inflamable, con los terminales de conexión hacia abajo. Montar cerca de la batería, pero nunca directamente encima de la misma (para evitar daños debido a los vapores generados por el gaseado de la batería). Utilice cables con una sección de 6 mm².
  • Página 45: Conexión De Un Inversor

    3.3.3. Puente entre pines 2 y 3: convencional (ver 1.2.1.) Desconexión de carga por baja tensión: 11,8V ó 23,6V Reconexión automática de la carga: 14V ó 28V 3.4 LED LED verde: se enciende o parpadea cuando se ha conectado la batería On: uno de los dos algoritmos convencionales Parpadeo: algoritmo BatteryLife LED amarillo: señala la fase de carga...
  • Página 46: Información Sobre La Carga De Las Baterías

    3.7 Información sobre la carga de las baterías El controlador de carga inicia un nuevo ciclo de carga cada mañana, cuando empieza a brillar el sol. La duración máxima del periodo de absorción queda determinada por la tensión de la batería medida justo antes de que se ponga en marcha el cargador solar por la mañana: Tensión de la batería Vb (al Tiempo máximo de absorción...
  • Página 47: Resolución De Problemas

    4. Resolución de problemas Problema Causa posible Solución Conecte las placas PV Conexión inversa de las placas PV El cargador no correctamente funciona No hay fusible Ponga un fusible de 20A Conecte la batería Fusible fundido Conexión inversa de la batería correctamente Sustituya el fusible Compruebe las conexiones de...
  • Página 48: Especificaciones

    5. Especificaciones Controlador de carga BlueSolar MPPT 75/15 Tensión de la batería AutoSelect 12/24 V Corriente máxima de la batería 15 A Potencia PV máxima, 12V 1a,b) 200 W (rango MPPT 15 V a 70 V) Potencia PV máxima, 24V 1a,b) 400 W (rango MPPT 30 V a 70 V) Desconexión automática de la carga Sí, carga máxima 15 A...
  • Página 58 Figure 2: Battery management options EN: No bridge: BatteryLife algorithm NL: Geen brug: BatteryLife algoritme FR: Pas de pont : Algorithme BatteryLife DE: Keine Überbrückung: BatteryLife Algorithmus ES: Ningún puente: algoritmo BatteryLife SE: Ingen brygga: BatteryLife-algoritm EN: Bridge between pin 3 and 4: Low voltage disconnect: 11.1V or 22.2V Automatic load reconnect: 13.1V or 26.2V NL: Brug tussen pin 3 en 4:...

Este manual también es adecuado para:

Bluesolar mppt 100/15

Tabla de contenido