Troubleshooting - HAMPTON BAY 724-491 Manual De Instrucciones

STEP 5:
INSTALLATION AND REMOVAL OF TRACK HEAD (REFER TO Fig.6)
FIG. 6
GROUND INDICATOR
INSTALLATION
1. Push the top portion of the head adapter into the slot of the track section.
2. Pull down the adapter's locking tab.
3. Turn "Ground Indicator" tab towards the ground groove on track to align ground tab with ground conductor.
4. Adapter can move to any position along the track section. Lighting fixture will adjust to any position.
REMOVAL
1. Pull down the adapter's locking tab.
2. At the same time, rotate the adapter 90 degrees and remove from track.
STEP 6:
INSTALLING NEW BULB OR RELAMPING
1. Turn the power off. Make sure that the bulb is cool before re-lamping the fixture.
2. Pull down on the track head adapter sleeve and twist fixture a 1/4 turn.
3. Unscrew the spring clip.
4. Push in slightly and twist the bulb to unplug it from the socket.
5. Replace with new bulb and install the spring clip.
6. Replace the track head onto the track. Pull down the adapter sleeve and twist fixture a 1/4 turn.
CAUTION: Please refer to the re-lamping label located on the fixture for recommended maximum wattage.
TROUBLE SHOOTING:
Problem
Light Bulb will not illuminate.
Fuse blows or circuit breaker
trips when light bulb is
illuminated.
PRODUCT MAINTENANCE:
1. To clean the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse
at the fuse box.
2. Use a dry or slightly dampened clean cloth (use clean water, never use a solvent) to wipe the interior and exterior
surfaces of the fixture.
3. Allow the fixture to dry completely before power is restored.
CAUTION: Do not use chemical solvents or harsh abrasives to clean fixture as damage to the fixture or various
components may occur remedying the fixture inoperable.
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of
five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation,
and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that
the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way
not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not
relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the
warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any
consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the
replacement or repair of said product.
TRACK
GROUND GROOVE
Possible Cause
1. Light bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.
Crossed wires or power wire is
grounding out.
LIMITED WARRANTY
NOTICE:
1. CONNECTOR IS DESIGNED TO LOCK INTO
TRACK SECTION BY TURNING CONNECTOR
IN ONE DIRECTION ONLY.
2. TURN "GROUND INDICATOR" TAB TOWARDS
THE GROUND GROOVE ON TRACK TO ALIGN
GROUND TAB WITH GROUND CONDUCTOR.
Corrective Action
1. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace switch.
Check wire connections.
5