Eu Declaration Of Conformity - Binks AX260L-5 Manual De Servicio

EN
In this part sheet, the words wARNINg, CAUtIoN and NotE are used to
emphasize important safety information as follows:
wARNINg
!
Hazards or unsafe practices which
could result in severe personal
injury, death or substantial property
damage.
Read the following warnings before using this equipment.
READ tHE MANUAL
Before operating finishing equipment, read and understand all
safety, operation and maintenance information provided in the
operation manual.
wEAR SAfEty gLASSES
Failure to wear safety glasses with side shields could result in
serious eye injury or blindness.
DE-ENERgIzE, DEPRESSURIzE, DISCoNNECt AND LoCk
oUt ALL PowER SoURCES DURINg MAINtENANCE
Failure to De-energize, disconnect and lock out all power supplies
before performing equipment maintenance could cause serious
injury or death.
oPERAtoR tRAININg
All personnel must be trained before operating finishing
equipment.
EqUIPMENt MISUSE HAzARD
Equipment misuse can cause the equipment to rupture,
malfunction, or start unexpectedly and result in serious injury.
kEEP EqUIPMENt gUARDS IN PLACE
Do not operate the equipment if the safety devices have been
removed.
PRojECtILE HAzARD
You may be injured by venting liquids or gases that are released
under pressure, or flying debris.
PINCH PoINt HAzARD
Moving parts can crush and cut. Pinch points are basically any
areas where there are moving parts.
AUtoMAtIC EqUIPMENt
Automatic equipment may start suddenly without warning.
It IS tHE RESPoNSIBILIty of tHE EMPLoyER to PRoVIDE tHIS INfoRMAtIoN to tHE oPERAtoR of tHE EqUIPMENt.
foR fURtHER SAfEty INfoRMAtIoN REgARDINg tHIS EqUIPMENt, SEE tHE gENERAL EqUIPMENt SAfEty BookLEt (77-5300).
Note: Read and follow all instructions and safety precautions
before using this equipment.
Product Descriptions
AX260L-5 AX260L Air Motor Assembly
AX260L-6 AX260L Air Motor Assembly
AX260L-7 AX260L Air Motor Assembly
AX260L-8 AX260L Air Motor Assembly
This product is designed for use with Solvent based and
Waterborne materials. Suitable for use in Zone 1 and 2,
Protection Level: II 2 G X
Manufacturer: Finishing Brands
Justus-von-Liebig - Strasse,
63128 Dietzenbach. DE
!
CAUtIoN
Hazards or unsafe practices which
could result in minor personal injury,
product or property damage.
wARNINg
!

eU Declaration of Conformity

We: Finishing Brands declare that the above product conforms with the Provisions of Machinery
Directive 2006/42/EC and the ATEX Directive 94/9/EC by complying with the following statutory
documents and harmonized standards:
Machinery Safety Standards EN ISO 12100, EN ISO 4413, EN ISO 4414 & EN12621
Explosion Prevention Potentially Explosive Atmospheres EN 1127-1
Non-electrical Equipment for Potentially Explosive Atmospheres BS EN 13463-1
Constructional Safety for Potentially Explosive Atmospheres EN 13463-5
Providing all conditions of safe use stated within the product manuals have been complied with
and that the final equipment into which this product is installed has been re-assessed as required,
in accordance with essential health and safety requirements of the above standards, directives and
statutory instruments and also installed in accordance with any applicable local codes of practice.
Binks reserves the right to modify equipment specification without prior notice.
2 / 10
NotE
Important installation, operation or
maintenance information.
INSPECt tHE EqUIPMENt DAILy
Inspect the equipment for worn or broken parts on a daily basis.
Do not operate the equipment if you are uncertain about its
condition.
NEVER MoDIfy tHE EqUIPMENt
Do not modify the equipment unless the manufacturer provides
written approval.
kNow wHERE AND How to SHUt off tHE EqUIPMENt
IN CASE of AN EMERgENCy
PRESSURE RELIEf PRoCEDURE
Always follow the pressure relief procedure in the equipment
instruction manual.
NoISE HAzARD
You may be injured by loud noise. Hearing protection may be
required when using this equipment.
HIgH PRESSURE CoNSIDERAtIoN
High pressure can cause serious injury. Relieve all pressure before
servicing. Spray from the spray gun, hose leaks, or ruptured
components can inject fluid into your body and cause extremely
serious injury.
StAtIC CHARgE
Fluid may develop a static charge that must be dissipated through
proper grounding of the equipment, objects to be sprayed and all
other electrically conductive objects in the dispensing area. Improper
grounding or sparks can cause a hazardous condition and result in
fire, explosion or electric shock and other serious injury.
PRoP 65 wARNINg
WARNING: This product contains chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm.
D. Smith (General Manager)
16th April 2012
77-2957-R3.0