Idiomas disponibles
Idiomas disponibles
i
I (
) With the help of another person inside the show-
er box, check the closing of the door and the alignment of the glass
panels with the profile of the tray. If necessary, insert the transpar-
ent plastic wedges (included) to compensate for any gaps between
the shower and the glass panel (
ble-face tape from the plastic blocks and position them as shown
(
).
i
I (
the compensator"G"and make holes in the profile of the glass pan-
el "H"; then attach the glass panel as shown.
(
) Using the appropriate tool, insert the gasket as shown,
using care in positioning it.
i
I (
) Use as a reference the holes of the com-
pensator "E", and make holes in the profile of the glass panel "I",
then attach it to the compensator (
(
) Using the appropriate tool, insert the gasket as shown,
using care in positioning it.
i
I (
) Remove the plastic spacers from under the door
and place the two terminals on the under-door gasket (
Remove the film from the double-faced tape and then apply the
gasket to the door (
magnet adheres perfectly to the double-faced tape of the end.
i
I (
) Screw the shower hose onto the support,
placing the mesh filter, screw in the shower head and apply the
shelf, as shown (
).
Then install the cover on the drain pipe (
requested, position the footboard (optional) on the tray, as shown
(
).
with 4 screws M5X14, secure the closure cover
of the boiler (detail 4).
i
I (
) Before applying silicone, check that the glass pan-
els have been attached to the compensators.
Apply silicone to along the entire length of the inner profile of the
glass panels and of the tray. First make sure that the surfaces are
clean.
i
I (
) Fasten the two heads to the end of the under-
door profile.
Apply a line of silicone to the bottom of the profile, along its en-
tire length, as shown.
i
I (
) Then fasten the profile to the shower tray, so
that it lines up with the profiles of glass panels "I" (
"H" (
) as shown.
(
) Keep the profile in position with sticky tape, until the sil-
icone is completely dry.
). Remove the strip of the dou-
) Use as a reference the holes of
).
), ensuring that the profile with the
) and, if it has been
(
) Apply silicone to along the entire length of the outer pro-
file of the glass panels. Make sure that the surfaces are clean.
(
) After 24 hours, remove the plastic blocks that hold the glass
panels in place.
i
I (
) Click on profiles "U", as shown.
I (
) Fasten the plate for column closure with 4 screws M5x12.
I (
) Snap in the profiles "J" on the sides of the column and
the "U" profiles on the wall compensators as shown (
I (
) Fasten the plate for column closure with 4 screws M5x12.
i
I (
making sure that they are inserted in the correct direction.
i
I (
Make sure that the seal to be attached to the door is different to
the others (
).
Fasten the block for the fastening of the top with the two plastic
grub screws provided (
i
I (
wall-mounted glass panels (or on the "L"-shaped profiles) and secure
them to the supports with the eccentrics and screws indicated.
If it is necessary, turn the cams so that the slot lines up with the
holes in the supports.
(
) Further secure the top using the indicated screws.
i
I (
making sure that they are inserted in the correct direction.
Part of the support must be removed and thrown away.
i
I (
Make sure that the seal to be attached to the door is different to
the others (
Fasten the block for the fastening of the top with the two plastic
grub screws provided (
i
I (
the crossbar, making sure that it is flush with the wall. Check that it
is level and mark the 3 holes to be drilled (
Drill the holes, insert the dowels and reposition the L-shaped pro-
file (
).
Fasten the L-shaped profile to the wall as indicated (
i
I (
check that it is level and mark the holes for drilling (
Drill the holes, insert the dowels and reposition the profile (
) and
Fasten the L-shaped profile to the wall as indicated (
i
I (
) Apply covering corner A, as shown, by removing the film
from the double-face adhesive and gluing it under the profiles.
The purpose of the corner is to cover any space which is created in the
area where the profiles are coupled.
) Insert the rubber supports for the top cover,
) Then insert the seals.
).
).
) Set the top on the gaskets of the profiles of the
) Insert the rubber supports for the top cover,
) Attach the seals.
).
).
) Rest the"L"-shaped profile (the shortest one) on
) Place the other "L"-shaped profile as shown,
).
).
).
).
).
).
