Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TRACTOR
Always observe safety rules when performing
any maintenance,.
BRAKE
OPERATION
if tractor
requires
more than five (5) feet to
stop at highest
speed
in highest
gear on a
level, dry concrete
or paved
surface,
then
brake must be serviced.,
(See "TO CHECK
..........
BRAKE"
in the Service
and Adjustments
section
of this manual).
TIRES
.
Maintain
proper
air pressure
in all tires
(See the sides of tires for proper PSI).
• Keep tires free of gasoline,
oil, or insect
control chemicals
which can harm rubber.
• Avoid
stumps,
stones,
deep ruts, sharp
objects and other hazards that may cause
tire damage.
NOTE: To seal tire punctures
and prevent
fiat tires due to slow leaks, tire sealant
may
be purchased
from your local parts dealer.
Tire sealant
also prevents
tire dry rot and
corrosion.
OPERATOR
PRESENCE
SYSTEM
AND
REVERSE
OPERATION
SYSTEM
(ROS)
Be sure
operator
presence
and
reverse
operation
systems
are working
properly.
If
your tractor does not function
as described,
repair the problem
immediately_
. The engine
should
not start
unless
the
brake
pedal is fully depressed,
and the
attachment
clutch control
is in the disen-
gaged position.
CHECK
OPERATOR
PRESENCE
SYSTEM
. When the engine is running,
any attempt
by the operator
to leave the seat without
first setting the parking
brake should shut
off the engine.
• When the engine
is running
and the at-
tachment
clutch is engaged,
any attempt
by the operator
to leave the seat should
shut off the engine.
• The attachment
clutch should never oper-
ate unless the operator
is in the seat.
@
ROS "ON" Position
Engine "ON" Position
(Normal Operating)
CHECK
REVERSE
OPERATION
(ROS)
SYSTEM
" Whentheengineis
runningwiththe
ignition
switch in the engine "ON" position and the
attachment
clutch engaged,
any attempt
by the operator
to drive in reverse should
shut off the engine,
• When the engine is running with the ignition
switch in the ROS "ON" position
and the
attachment
clutch engaged,
any attempt
by the operator
to drive in reverse should
. NOT shut off the engine°
BLADE
CARE
For best results mower blades must be sharp,.
eplace worn, bent or damaged
blades.
CAUTION:
Use
only
a replacement
blade approved
by the manufacturer
of your
tractor. Using a blade not approved
by the
manufacturer
of your tractor
is hazardous,
could
damage
your tractor
and void your
warranty.
BLADE
REMOVAL
1o Raise mowerto
highest position to allow
access to blades.
NOTE: Protect your hands with gloves and/
or wrap blade with heavy cloth.
2.
Remove
blade bolt by turning
counter-
clockwise_
3,
Install new blade with stamped
"GRASS
SIDE" facing the ground°
IMPORTANT:
To ensure
proper
assembly,
center hole in blade must align with star on
mandrel
assembly_
4.
Install and tighten
blade
bolt securely
(45 - 55 Ft. Lbso torque).
IMPORTANT:
Special
blade
bolt
iS heat
treated.
Slar
Center Hole
Blade Bolt
Mandrel
(Special) "_-_),_""
Assembly
Blade
PARA AJUS'f
LA SEGADOI
La posiciSn de
a qu6 altura s,
::;;:_!i!_i!!!:i
• Coloque la
la altura de,.
La gama de I;
damente 1 a
desde el sue!{
el motor no e_
aproximadas
condiciones d
del tipo del c6
• El c6sped p_
mente a 2 -
fria y sobn
calurosos_ f
able y de rr
y despu6s
, Para obten_
c6sped que
debe segars
ativamente
PARA OPERt
Su tractor vie
sensor que el
el motor estb. t
cesorio est& e
bajarse del as
que mantene
mente en et
vacile o se ap
en terreno dis
t.
Seleccion,
2_ Baje la s_
tamiento c
3.
Haga arra
engancha
accesorio_
20
Tabla de contenido
