General Information; Service Information; Installation - Zanussi Z20 El Manual Del Propietario

GENERAL INFORMATION

The central vacuum is designed for dry pick-up of household dirt and dust. Avoid
picking up hard or sharp objects with this system to prevent hose and plastic pipe
damage or clogs.
This manual will cover the final steps of installation of the power unit in your
home. It will also provide the necessary information for maintenance and trouble
shooting, in the unlikely event that it will be needed. If you require further
information about installation or inquires on the product please contact your local
authorized dealer/distributor.
INSTALLATION SAFETY EQUIPMENT
For wall preparations and cover preparations,
safety equipment such as helmet, gloves, goggles
and hearing protection are recommended.
CAUTION
Use caution when drilling holes in walls as gas pipelines and water pipes and
electrical wires may be present.
If you have any questions regarding the product, spare parts, service, warranty or
anything else, please contact your local authorized dealer or distributor.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical current to reduce the risk of
electrical shock. This appliance is equipped with a cord having an equipment-
grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING
Improper connection of the equipment-grounding conductor can result in electri-
cal shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded, or if the plug does not fit into an
outlet. Do not modify the plug provided with the appliance.
WARNING
If the supply cord is damaged, it must be replaced by a special cord available
from your local authorized dealer/distributor.

SERVICE INFORMATION

The instructions in this booklet serve as a guide to routine maintenance.
For additional information, contact you're nearest authorized dealer/distributor.
RATING PLATE
The type, model, and serial numbers are indicated on the rating plate located on
the control panel or motor hood. For prompt and complete service information,
always refer to these numbers when inquiring about service.
WARNING
Non-observance of the safety directions may result in bodily harm.
PRODUCT DIMENSIONS
Refer to page 39 - Image 1
WASTE OF ELECTRIC AND ELECTRICAL
EQUIPMENT (WEEE)
This symbol on the product or on its packaging indicates that this product may
not be treated as household waste. Instead it should be handed over to appli-
cable collection point for the recycling of electronics and electrical equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For
more detailed information about this product, please contact your local waste
disposal service or the shop where you purchased the product.

INSTALLATION

If you home is fitted with the system of plastic pipes and inlet valves and you
are ready to install the central power unit. If your home is not fitted for a central
vacuum system, you can contract to have the Central Vacuum System installed
by a professional by contacting your local dealer or distributor or choose to
do-it-yourself.
The central power unit should be located as far away from the general living area
as possible, yet accessible so you can remove the dirt receptacle, reach the filter,
and inspect the central power unit. A typical location would be in a garage, where
you could vacuum your car or garage area, and where emptying the dirt receptacle
and cleaning the filter would be more convenient. Other suitable locations are in
the basement, laundry room, or ventilated storage room.
CAUTION
Use caution when drilling holes in walls as gas pipelines and water pipes
and electrical wires may be present. Holes in the masonry are only allowable
through it if its standing stability is not impaired. Holes in wood studs should
be drilled. Depending on what material your home is built with, use the
appropriate anchors to hang your power unit. Power unit simply slides onto
mounting bracket and clicks into place.
Refer to page 39 - Image 3
• Place the central power unit in a place that is removed from the general living
area. The exhaust should be easy to connect to a ventilation pipe. This can be
done regardless of the house's construction material.
• Locate the two low voltage wires near the main pipe. Remove the insulation
from the low volt wire. Insert the low volt wire into the spring loaded low
volt connectors. Be certain you comply with your local electrical codes and
regulations.
Refer to page 39 - Image 4
• Make sure there is a dedicated electric socket for the power unit.
• Plug in your CVS with the supplied power cord.
4