GE 16 Instrucción De Instalación página 8

Installation instructions
INSTALLING THE WATER
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect _M Refrigerator Tubing (WX08X10006,
WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation is
with a GE RV Kit. For other reverse osmosis water systems,
follow the manufacturer's recommendations.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and lead
to water leakage or flooding. Call a qualified plumber to
correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up the
water line to the hot water line.
If you use your refrigerator before connecting the water
line, make sure the feeler arm is in the STOP (up) position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power drill)
during installation, be sure the device is double insulated or
grounded in a manner to prevent the hazard of electric
shock, or is battery powered.
All installations must be in accordance with local plumbing
code requirements.
WHAT YOU WILL NEED
• Copper or GE SmartConnect
TM
Refrigerator
Tubing kit, 1/4" outer diameter to connect the
refrigerator to the water supply. If using copper, be sure
both ends of the tubing are cut square.
To determine how much tubing you need: measure the
distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8'
(2.4 m). Be sure there issufficient extra tubing
(about 8' [2.4 m] coiled into 3 turns of about 10"
[25 cm] diameter) to allow the refrigerator to move out
from the wall after installation.
LINE (oNSOME
MODELS)
WHAT YOU WILL NEED
(CONT.)
GE SmartConnect 'M Refrigerator Tubing Kits are available
in the following lengths:
6' (1.8 m) - WX08X10006
15' (4.6 m) - WX08X10015
25' (7.6) m) - WX08X10025
Be sure that the kit you select allows at least 8' (2.4 m) as
described above.
NOTE:
The
only GE approved plastic tubing is
that supplied in
GE
SmartConnect
TM
Refrigerator
Tubing kits. Do not use any
other plastic water
supply line because the line is under pressure at
all times, Certain types of plastic will crack or
rupture with age and
cause water damage to your home=
• A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra cost
from your dealer or from Parts and Accessories,
1.800.661.1616.
• A cold water supply.
The water pressure must be
between 20 and 120 p.s.i. (1.4-8.1 bar). ,,_
• Straight and Phillips V
blade screwdriver,
=
Two 1/4"
outer diarrleter compression nuts and
2 ferrules (sleeves)--t0 connect ,__
the copper tubing to the shutoff
valve and the refrigerator water valve.
OR
If you are using a GE SmartConnect 'M Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
If your existing copper water line has a flared fitting at
the end, you will need an adapter (available at plumbing
supply stores) to connect the water line to the refrigerator
OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect 'M
Refrigerator tubing.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.