Special Modes; Minimization Mode - Accu turn 1500 Manual Para El Operador

5.4.2-1
5.4.2-2
5.4.2-3
5.4.2-4
5.4.2-5
5.4.2-6
52
Operations
5.4 5.4

Special modes.

Special modes.
Selecting the "F" key allows the operator to use: Selecting the "F" key allows the operator to use:
- -

Minimization mode,

Minimization mode,
- - Weight units toggle mode, "oz", Weight units toggle mode, "oz",
- - Dimensional units toggle mode, "mm", Dimensional units toggle mode, "mm",
- Counter Functions,
-
User selector,
5.4.1 Minimization mode.
5.4.1 Minimization mode.
Select this mode if a wheel requires a weight of 3 oz.
Select this mode if a wheel requires a weight of 5 oz.
(80 grams) or more in a plane in order to be balanced.
• Ensure the wheel is properly mounted. (80 grams) or more in a plane in order to be balanced.
• Ensure the wheel is properly mounted.
• Select the "F" key (Figure 5.4.2-1).
• Select the "F" key (Figure 5.4.2-1).
To exit the Minimization mode, select:
NOTE: To exit the Minimization mode, select:
"FINE"-key.
"FINE"- key.
all minimization data are stored into memory. The
All minimization data are stored into memory. The
operator can select Minimization again to proceed
operator can select Minimization again to proceed
with the next step.
with the next step.
During minimization, the left display shows the steps
During minimization, the left display shows the steps
in the following sequence:
in the following sequence:
Step 1 (Figure 5.4.2-2):
• Rotate the valve to the 12 o'clock position. Step 1 (Figure 5.4.2-2):
• Rotate the valve to the 12 o'clock position.
• Select the "F" key.
• Select the "F" key.
Step 2 (Figure 5.4.2-3):
• Spin the wheel. Step 2 (Figure 5.4.2-3):
• Spin the wheel.
The unit checks if a minimization is recommended.
The unit checks if a minimization is recommended.
Step 3:
Step 3:
Minimization not required (Figure 5.4.2-4).
• Exit Minimization Mode. Minimization not required (Figure 5.4.2-4).
• Exit Minimization Mode.
Minimization recommended (Figure 5.4.2-5).
Minimization recommended (Figure 5.4.2-5). • Mark the tire at 180° to the valve position
• Mark the tire at 180° to the valve position • Remove the wheel from the balancer.
• Remove the wheel from the unit.
• Use a tire changer to rotate the tire so that the mark
• Use a tire changer to rotate the tire so that the mark
is in line with the valve (Figure 5.4.2-6).
is in line with the valve (Figure 5.4.2-6).
• Mount the wheel on the balancer.
• Mount the wheel on the balancer.
• Select the "F" key.
• Select the "F" key.
Step 4 (Figure 5.4.2-2):
Step 4 (Figure 5.4.2-2): • Rotate the valve to the 12 o'clock position.
• Rotate the valve to the 12 o'clock position.
• Select the "F" key.
• Select the "F" key.
Step 5 (Figure 5.4.2-3):
Step 5 (Figure 5.4.2-3):
• Spin the wheel.
• Spin the wheel.
The unit checks if additional minimization is
The unit checks if additional minimization is
recommended.
recommended.
Operator's Manual ACCU 1500