Expanded Function - Denon DN-T645 Instrucciones De Operación

ENGLISH

EXPANDED FUNCTION

16
Multiple units of the DN-T645/625 or other DENON products (DN-780R etc.) can be used together for longer play
and recording time, simultaneous recording and other functions.
2 CASCADE (MULTIPULE CONTINUOUS) OPERATION
• Refer to figure 1 to connect the equipment.
• Use a single RCA cable to connect the units' CASCADE OUT jacks with the units' CASCADE IN jacks.
• When the first and last units are connected as shown in figure 1, recording and playback are performed
endlessly. Note that in the recording mode, previous recordings are overwritten.
• If the first and last units are not connected, operation stops at the last unit.
Cascade playback
1. Load the discs and the tapes you want to play in all
the units. Make sure the Dolby NR and play mode
are properly set.
2. Use the RELAY MODE switch !3 to set the relay
mode of all units to " CASCADE" .
) button t on unit 1.
1 3
3. Press the play/pause (
Playback starts.
• Playback on CD ends, Deck starts playing.
• Playback on Deck ends, playback starts on unit
2's CD.
4. Playback stops when the stop button on the unit
currently playing is pressed.
NOTE :
• The front and rear sides of the tape are played
continuously, regardless of the position of the
REV. MODE switch.
External synchronized recording
The synchronized recording can be use when the DN-T645/625 is used in combination with DENON other
product (DN-780R etc.).
When the CD player's play/pause button and the deck's play button are pressed, a synchronized signal for starting
is output from the EXT. SYNC. jack. When the stop buttons on the CD player and the deck are pressed a
synchronized signal for stopping is output.
• Refer to figure 2 to connect the equipment.
• Use a single RCA cable to connect the units' EXT. SYNC. OUT jacks with the units' EXT. SYNC. IN jacks.
✽ Set the infrared remote sensors of all the units to " OFF" when using this function. Also set the same infrared
remote control codes for all the units. (Refer to " PRESET FUNCTIONS AND OPERATIONS" (See page 18).)
Failure to make these settings could result in malfunction.
1. Load the CD into DN-T645/625. Load unrecorded cassette tapes into all decks.
2. Set the reverse mode and Dolby NR of all decks.
16
Cascade recording
1. Load cassette tapes on which nothing is recording
into decks of all the units and set the Dolby NR
modes. Adjust the recording level for Decks.
2. Use the RELAY MODE switch !3 to set the relay
mode of all units to " CASCADE" .
) button @9 on Deck of all
4
3. Press the rec/rec mute (
the units.
✽ Check that all Decks are set to the recording
pause mode.
✽ Also set the direction of tape travel at this time.
) button @9 on unit 1.
0 1
4. Press the Deck play ( or
Recording starts.
• Once recording on Deck ends, recording starts
on Deck of the next unit.
• Deck is set to the recording pause mode on unit
on which recording has ended.
✽ Cascade recording stops if Deck of any of the
units is set to anything other than the recording
pause mode.
) button @9 on the
5. Recording stops when the stop ( 2
deck currently recording is pressed. After doing
) buttons @9 on all the decks.
this, press the stop ( 2
NOTE :
• The front and rear sides of the tape are recorded
continuously, regardless of the position of the
REV. MODE switch.
3. Adjust the twin recording level of DN-780Rs. (Master/Slave switch set to OFF.)
4. Press the CD SYNC. button #5 of DN-T645/625 to display " Normal Copy" . And press the select knob !2 to set
the CD SYNC. mode. And press the Twin recording button of DN-780R.
) button t of DN-T645/625. Recording starts all decks.
5. Press the play/pause ( 1 3
2
6. Press the stop ( ) button on one of the units. The all unit is also set to the stop mode.
NOTES :
• Use tapes of the same times (lengths) as far as possible.
• Note that the auto reverse timing is not synchronized.
Figure 1
Figure 2
L R
R L
unit 1 DN-T645
unit 2 DN-T645
DN-T645
DN-780R