Tabla de contenido
Idiomas disponibles
Idiomas disponibles
LIstenIng to Your IPoD/IPhone through the
Dock connector
1.
If playing an iPhone, skip to the next step 3.
2.
If playing an iPod classic, touch or nano, insert the included
adapter into the two holes behind the dock connector and
press firmly to ensure a proper connection.
3.
Carefully place your device into the dock connector.
4.
Press the
on the top of the unit or the remote to power on
Tango TRX.
5.
Press the source button on the top of the unit or on the remote
until the iPod logo is illuminated as the source.
6.
Press play on the on the unit or on the remote. Use the controls
on the unit or the included remote to adjust the volume and
iPod functions.
Note: The unit will charge your device while docked.
LIstenIng to Your DevIce wIreLessLY over
BLuetooth
To listen to your music over the Bluetooth wireless connection,
you need to pair your device with Tango TRX.
1.
Make sure your device has Bluetooth capability.
2.
Press the
on the top of the unit or the remote to power on
Tango TRX.
3.
Follow the instructions listed in the manual of your device to
turn on the Bluetooth functionality to pair your device with
the unit.
4.
Pair your device with the unit by selecting Tango TRX from
your Bluetooth listings on your device or selecting yes. If
prompted, enter 0000 as the passcode.
5.
Press the source button on the top of the unit or the remote
until the LED under the Bluetooth logo is illuminated as
the source.
6.
Press play on your device and use the control dial on the unit
or the remote to adjust the volume.
7.
Use your device or the remote (for iPod/iPhone only) to control
music functions.
Note: Once you have successfully paired your device with Tango TRX, you will not
need to repeat the above steps. For each use, ensure that the unit source is set to
Bluetooth and that Bluetooth is enabled on your device.
While there is an incoming call for the iPhone, the music will pause. After finishing
the call, the music will resume playing.
usIng the Xtrememac aPP
For enhanced functionality and control, download the Tango TRX
app. It will allow you to control volume, EQ settings, play/pause
and other iPod functions directly from your iPhone or iPod touch.
10
IPU-TRX-13_user_guide_23950664C.indd 10-11
LIstenIng to Your DevIce through the
auXILIarY LIne-In jack
1.
Connect a 3.5mm audio cable (available at
www.xtrememac.com) to the headphone or line out jack of an
audio device and plug the other end of the cable into the Aux
jack on the back of the unit.
2.
Press the
on the top of the unit or the remote to power on
Tango TRX.
3.
Press the source button on the unit until the LED under the Aux
icon is illuminated.
4.
Press play on the device. Use the control knob on the unit to
control the volume.
aDjustIng Bass anD treBLe
While playing audio, press the bass or treble control on the unit
and use the control knob to adjust the setting. The LEDs on the
unit will illuminate from the center to indicate the level of bass
and treble at +/- 4 for each setting. You may also adjust the bass
and treble with the remote.
LeD InDIcators
SOURCE
The LED under the source icon will illuminate when pressing the
source control to indicate the source selected. Once selected the
LED will remain illuminated.
VOLUME
The LEDs will illuminate in sequence when adjusting the volume
to indicate volume level. The LEDs for volume will time out after 2
seconds and only the LED for the source will remain illuminated.
BASS/TREBLE
The LEDs on the unit will illuminate from the center to indicate
the level of bass and treble at +/- 4 for each setting. The LEDs for
volume will time out after 2 seconds and only the LED for the
source will remain illuminated.
trouBLeshootIng tIPs
no Power
Check AC adapter connection on unit
Connect the AC adapter into the jack in the back of the unit labeled
"18V
2.5A" and then plug the AC adapter into the wall outlet.
Check wall outlet function
Plug another device into the same outlet to confirm the outlet is
working.
11
8/11/11 11:20:33 AM
Tabla de contenido
