Important Safety Instructions; Set Up Calibration - Mirage BPS-150i Manual De Instrucciones

o w n e r s m a n u a l

IMPORTANT SAFETY INSTRUCTIONS

Read Instructions
All safety and operating instructions should be read before the product is operated.
Retain Instructions
The safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
Follow Instructions
All operating and use instructions should be followed.
Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Attachments
Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
Water and Moisture
Do not use this product near water– for example near a bath tub, wash bowl kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool.
Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and these openings must not be blocked or
covered. They should also never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
Power Sources
This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your product
dealer or local power company. For products intended to operate from battery power, or other
sources, please refer to the operating instructions.
Grounding or Polarization
This product may be equipped with a polarized alternating-current line plug (a plug having one
blade wide than the other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your obsolete outlet. DO NOT
defeat the safety purpose of the polarized plug.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by
the items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
Overloading
Do not overload wall outlets or extension cords, as this can result in a risk of fire or
electric shock.
Object and Liquid Entry
Never push objects of any kind in this product through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of
any kind on the product.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards.
Heat
This product should be situated away from heat sources such as radiators ,heat registers, stoves,
or other appliances (including amplifiers) that produce heat.
Non-use Periods
The power cord of the product should be unplugged from the outlet when left unused for a
long period of time.
Damage Requiring Service
This product should be serviced by qualified service personnel when;
(A) The power supply cord or the plug has been damaged, or
(B) Objects have fallen, or liquid has been spilled into the appliance, or
(C) The product has been exposed to rain, or
(D) The appliance does not operate normally or exhibits a marked change in sonic
performance, or
(E) The product has been dropped, or the enclosure has been damaged.
"MIRAGE", the "MIRAGE" logo, "The Original Bipolar Loudspeaker", "Omnipolar" and "API Accessories" are
trademarks of Audio Products International Corp. "Dolby", "Dolby Pro-Logic" and "Dolby Digital Surround"
are trademarks of Dolby Laboratories Licensing. DTS is a Trademark of Digital Theater Systems Inc.
SUBWOOFER CONNECTION TO YOUR
AUDIO/VIDEO SYSTEM
There are essentially two methods by which you can connect your Mirage subwoofer to your
audio/video system. The first is "The High Level Connection" and the second, "The Low
Level Connection". Your system components will dictate which method to use, but High
Level Connection can be used with virtually any receiver or amplifier.
In both methods, the left and right channel inputs are combined. That signal is then passed
through a variable (50Hz to 100Hz @ 18dB/octave) Low Pass Filter for seamless matching of
the subwoofer to the main satellite speakers.
CAUTION: (A) DO NOT USE BOTH LOW LEVEL AND HIGH LEVEL METHODS
SIMULTANEOUSLY. (B) TURN OFF ALL POWER IN YOUR STEREO SYSTEM
BEFORE PROCEEDING WITH THE INSTALLATION OF THE SUBWOOFER.
Using High Level Connections (see Diagram 1)
On the rear of your Mirage subwoofer cabinet is a block designated "High Level". This block
contains two pairs of speaker terminals. These should be connected to the speaker output
terminals of your amplifier or A/V receiver. Each pair of terminals are color coded black/red.
NOTE: These terminals will accept up to 18 Gauge speaker wire.
REMEMBER: Always connect red-to-red and black-to-black, when making the
connections between amp/receiver to subwoofer. If you inadvertently reverse
one of the connections (ie. red-to-black), you will notice a lack of bass from
your subwoofer.
Using the "Subwoofer Output" of an A/V Receiver or
Processor (See Diag. 2 - Low Level Connection1)
This method uses a single RCA-to-RCA interconnect cable to connect the "SUBWOOFER
OUTPUT" jack from your A/V receiver or processor to the subwoofer "INPUT". This method
does not remove low frequencies from your main speakers, and they will continue to reproduce
bass frequencies.
Using An External Crossover (See Diag. 3 Low Level
Connection 2)
This method uses a single RCA-to-RCA interconnect cable to connect the "SUBWOOFER
OUTPUT" jack from an external crossover to the "XOVER INPUT" of your subwoofer. This
method by-passes the subwoofer's built-in level and crossover controls; subwoofer functions are
controlled by the external crossover. (See External Crossover Owner's Manual for details.)

SET UP CALIBRATION

For best results when setting up your system, assume your normal listening position and have
another person perform the following adjustments:
1. Set the Subwoofer Level Control to its zero position. Set the Subwoofer LP Filter Control
to 50Hz. Set any loudness, bass/treble, and/or equalizer controls on your preamplifier or
integrated amp/receiver to their normal or mid-point positions.
2. Play a familiar CD, record, or video soundtrack that has substantial bass content.
3. Gradually turn the Subwoofer Level Control clockwise until you achieve a neutral balance
between the subwoofer's deep bass output and your main/satellite speakers.
4. Slowly turn the Subwoofer LP Filter Control clockwise to reach the best mid bass blend
with your main/satellite speakers. This will be the point at which the bass retains solid
impact and fullness.
If the mid bass becomes "boomy" or ill defined, you have gone too far and should turn
the control counter-clockwise to the best balance point. If the sound is too thin (i.e.,
male vocals are not full sounding) then turn the control clockwise to the best balance point.
NOTE: The Subwoofer Level Control is designed to control the balance between your
subwoofer and main/satellite speakers and should not be used as a substitute for the
bass or loudness controls on your amplifier or receiver. Adjust the subwoofer's level for
smoothest low frequency performance. If more bass is desired, then advance the bass and/or
loudness controls on your main amplifier or receiver.
LIMITED WARRANTY POLICY
Warranty Outside of The United States and Canada:
Product warranties may be legislated differently from one country to another. Ask your local
dealer for details of the LIMITED WARRANTY applicable in your country.
IMPORTANT: Please retain the carton and packing material for this MIRAGE
product to protect it in the event it ever has to be shipped to a service center for
repair. Product received damaged by a service center that has been shipped by the
end user in other than the original packaging, will be repaired, refurbished and
properly packaged for return shipment at the end user's expense.
WARRANTY FOR UNITED STATES
AND CANADA (see back cover)
2
s u b w o o f e r s