Description And Main Characteristics; Introduction; Features, Validity And Updates To The Manual; Keeping The Manual - Jacto PR-40 Manual De Instrucciones

THE COMPANY BELOW RESERVES THE RIGHT OF PROPERTY
OF THE FOLLOWING BOOKLET, PROHIBITS ANYONE FROM
REPRODUCING IT OR COMMUNICATING IT TO THIRD PAR-
TIES WITHOUT AUTHORISATION FROM THE OWNER.

1. Description And Main Characteristics

1.1. Introduction

This manual describes the operating and maintenance rules
and supplied spare parts of PR-40 Electronic pruning shears,
hereinafter simply referred to as "Shears".
The Shears have been designed and produced for pruning any
type of cultivation, especially vineyards, fir trees, fruit trees, ol-
ive trees and for gardening, nurseries and street tree pruning.
They must only be used for wooden materials and not for other
materials.
This manual is integral to the Shears, defines the purpose for
which it was built and contains all the information required for
proper and safe use.
Regular machine operation depends on its correct use and ad-
equate maintenance: it is advisable, therefore, to follow these
instructions carefully to prevent any situation that could com-
promise the machine's operation and durability. It is also im-
portant to follow that which is described in this manual since
the manufacturer declines any liability resulting from negli-
gence from not observing these norms, since it would result in
the warranty being annulled.
It is mandatory to ensure upon delivery that the Shears are in-
tegral and complete in all parts. Any complaints must be pre-
sented in written within 8 (eight) days from receiving the ma-
chine. The manufacturer can however be contacted at any time
for immediate and precise technical assistance and anything
required for optimum operation and maximum performance
of the equipment.
Upon receiving the product, carefully read the manual and
carefully follow the instructions contained in it.
1.2. Features, validity and updates to the
manual
All technical material or description in this manual is exclusive-
ly owned by the manufacturer who prohibits the complete or
partial reproduction of the same unless written approval has
been issued by the manufacturer.
Data, illustrations and descriptions in the manual cannot be
considered binding. The manufacturer reserves the right to
make changes at any time that it considers to be suitable for
improvement or for a constructive or commercial requirement.
This manual reflects the state of techniques at the time of
marketing the Shears and cannot be considered inadequate if
updated at a later date due to modifications of related legal
provisions.
26/69
The manufacturer, importer or dealer decline
any and all liability for damages caused by
the Shears to persons, animals or property,
resulting from use other than that described
in this manual, or due to damage caused by
negligence or by not observing the instructions
contained in this manual.

1.3. Keeping the manual

The manual should be carefully stored in a suitable area to
guarantee its physical integrity; it should be easy to access by
anyone authorized to consult it. The manual is an important
document that should accompany the Shears and all users
should be held responsible for safeguarding it.
The Shears are manufactured to conform to the provisions con-
tained in Directive 2006/42/EC. It is therefore equipped with
EC marking and accompanied by the following EC conformity
declaration.
The following manual is an integral part of
the product and must be stored carefully, in
order that it keeps its integrity and can be
consulted repeatedly throughout the entire
life of the Shears.

1.4. Statement of limited warranty

MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment
described in this manual and shall repair or replace parts and
components which, under normal operation and wear, in accor-
dance with technical recommendations, show DEFECTS IN MA-
TERIAL OR WORKMANSHIP, based on the following conditions.
This warranty consists in the repair or replacement free of
charge of those parts that should turn out to be faulty after
careful examination by the Manufacturer's Technical Depart-
ment or importer.
The warranty is limited only to defects in materials and ceas-
es to have effect should the damaged parts turn out to have
been tampered with or otherwise removed by unauthorised
personnel.
In the event of warranty service, the Shears shall be delivered
to the manufacturer in their original case equipped with all rel-
evant accessories (see Fig. 1).
For a warranty request, the equipment must be accompanied
by the completed registration card and proof of purchase (in-
voice or tax receipt).
• Manufacturer's warranty: 1 year (limited to 800,000 cuts
with average consumption 6Ah);
• The warranty starts from the date when the dealer's sales
invoice is issued (it is understood that during the battery