ATIKA HA 500/51 Manual Original página 18

• This device is not intended to be used by persons (including
children) with restricted physical, sensory or mental abilities
or a lack of experience and/or know-how unless they are
supervised by a person responsible for their safety or they
have been instructed by such a person on the use of the
device.
Supervise children to make sure they do not play with the
device.
more safety warnings
„Electrical safety"
• Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-section of at least
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm² for cable lengths over 25 m
• Long and thin connection lines result in a voltage drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
• Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
• The connector of the connection cable must be splash-proof.
• When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
• During the cutting operation, the supply cord must be
securely positioned to prevent the cord from snagged on
branches and the like.
• Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges.
• Wind off completely the cable when using a cable drum.
• Regularly check the cables and replace them if they are
damaged.
• Do not use any defective connection cables.
• Do not set up any provisional electrical connections.
• Do not hose down the device with water. (origin of danger
electric current).
• Never bypass protective devices or deactivate them.
• Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
• The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations – especially
regarding protective measures – must be observed.
more safety warnings
„Personal safety"
• The operator is responsible to third persons within the area
of operations.
• Adhere to national regulations that might specify an age limit
for the user of the unit.
• Wear suitable protective equipment when working:
− hairnet in case of long hair
− protection gloves
− eye and ear protection
18
more safety warnings
„Power tool use and care"
• Do not modify the device or parts of the device respectively.
• After a longer period of use, accessible metallic parts and
accessories may be hot.
• Switch off machine and pull out power plug out of the power
outlet in case of:
the cutting tool comes into contact with soil, stones, nails
or other foreign objects (
tool/machine is damaged)
− Carrying out repair work.
− Performing maintenance and cleaning work.
− Removal of faults (including blocking of knives).
Transport.
−
− Leaving the machine
interruption).
• Check the machine for possible damage:
− Before further use of the machine the safety devices
must be checked carefully for their proper and intended
function. Only operate the machine with complete and
correctly attached safety equipment and do not alter
anything on the machine that could impair the safety.
− Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must
be correctly installed and fill all conditions to ensure
perfect operation of the machine.
− Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
− Damaged or illegible safety labels have to be replaced.
• Store unused devices in a dry, locked place.
more safety warnings
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
more safety warnings
„Hedge trimmer safety warnings"
• Stop the hedge trimmer when moving to another work place.
• Always hold the hedge trimmer with both hands - one hand
on the front handle and the other on the rear handle.
• Make sure that you can step back safely without hindrances.
• Before trimming, remove all foreign objects (e.g. stones,
branches, wires, etc.). While working watch out for further
foreign objects.
• Be sure that the cutting tool already moves before you start
cutting.
• Caution! The cutting tool stops delayed after the machine is
switched off. Do not try to slow down the cutting tool by the
hand.
check whether the cutting
(also during
„Service"
temporary