Tabla de contenido
Apéndices
nowledged for synchronization")
1.2 Messages not recorded during recor-
ding
I Channel mode messages
G Local On/Off (Controller number 122)
Status
2nd byte
3rd byte
BnH
7AH
vvH
n=MIDI channel number : 0H–FH (ch.1–ch.16)
vv=Value
: 00H, 7FH (Local Off, Local On)
G All notes off (Controller number 123)
Status
2nd byte
3rd byte
BnH
7BH
00H
n=MIDI channel number : 0H–FH (ch.1–ch.16)
* When an All Note Off message is received, all notes of the corresponding channel that
are on will be sent Note Off's, and the resulting Note Off messages will be recorded.
1.3 Messages acknowledged for synchro-
nization
I System Common messages
G Tune Request
Status
F6H
G MIDI Time Code Quarter Frame Messages
MIDI Time Code Quarter Frame Messages can be transmitted while the MC-80 is running
(Playing or Recording) if the SYSTEM parameter "Mode" is "Master" and "MTC Sync out"
is "OUT1" or "OUT2" in the SYSTEM parameter. The transmitted time counts are summed
to "MTC Offset Time" as the song top is "00:00:00:00".
The MC-80 synchronizes with the time counts which are summed to "MTC Offset Time" as
the song top is "00:00:00:00" if the SYSTEM parameter "Mode" is "Slave (MTC)."
Status
Second
F1H
mmH (= 0nnndddd)
nnn = Message type :
0 = Frame count LS nibble
1 = Frame count MS nibble
2 = Seconds count LS nibble
3 = Seconds count MS nibble
4 = Minutes count LS nibble
5 = Minutes count MS nibble
6 = Hours count LS nibble
7 = Hours count MS nibble
dddd = 4 bit nibble data : h–FH (0–15)
Bit Field is assigned as follows.
Frame Count xxxyyyyy
xxx
Reserved (000)
yyyyy
Frame No.(0-29)
Seconds Count
xxyyyyyy
xx
Reserved (00)
yyyyyy
Seconds (0-59)
Minutes Count
xxyyyyyy
xx
Reserved (00)
yyyyyy
Minutes (0-59)
Hours Count
xyyzzzzz
x
Reserved (0)
yy
Time Code type
0 = 24 Frames / Sec
1 = 25 Frames / Sec
2 = 30 Frames / Sec (Drop Frame)
3 = 30 Frames / Sec (Non Drop Frame
zzzzz
Hours (0-23)
G Song Position Pointer
Status
2nd byte
3rd byte
F2H
mmH
llH
152
mm, ll=value : 00 00H–7F 7FH (0–16383)
I System Realtime Messages
G Timing Clock
status
F8H
* Received when "Mode" in the SYNC window (press [TOOLS] followed by [F3 (MIDI)]
and then [F3 (SYNC)]) is set to "Master."
G Start
status
FAH
* Received when "Mode" in the SYNC window (press [TOOLS] followed by [F3 (MIDI)]
and then [F3 (SYNC)]) is set to "Master" or "Remote."
G Continue
status
FBH
* Received when "Mode" in the SYNC window (press [TOOLS] followed by [F3 (MIDI)]
and then [F3 (SYNC)]) is set to "Master" or "Remote."
G Stop
status
FCH
* Received when "Mode" in the SYNC window (press [TOOLS] followed by [F3 (MIDI)]
and then [F3 (SYNC)]) is set to "Master" or "Remote."
I System Exclusive Message
G MIDI Machine Control (MMC)
* Received when the MMC Mode parameter ("MIDI INPUT SWITCH"
window/[TOOLS]-[F3 (MIDI)]-[F3 (SYNC)]) is Slave.
❍ STOP (MCS)
status
Data byte
F0H
7FH, dev, 06H, 01H
Byte
Remarks
F0H
Exclusive status
7FH
Universal System Exclusive Realtime Header
7FH
Device ID
06H
MMC command message
01H
STOP (MCS)
F7H
EOX (End of Exclusive)
❍ DEFERRED PLAY (MCS)
status
Data byte
F0H
7FH, dev, 06H, 03H
Byte
Remarks
F0H
Exclusive status
7FH
Universal System Exclusive Realtime Header
7FH
Device ID
06H
MMC command message
03H
DEFERRED PLAY (MCS)
F7H
EOX (End of Exclusive)
❍ LOCATE (MCP)
• Format2—LOCATE [TARGET]
status
Data byte
F0H
7FH, dev, 06H, 44H, 06H, 01H,
hrH, mnH, scH, frH, ffH
Byte
Remarks
F0H
Exclusive status
7FH
Universal System Exclusive Realtime Header
7FH
Device ID
06H
MMC command message
44H
LOCATE (MCP)
06H
Byte count
01H
"TARGET"sub-Command
hrH
Standard Time Specification with subframes (type{ff})
mnH
scH
frH
ffH
F7H
EOX (End of Exclusive)
status
F7H
status
F7H
status
F7H
Tabla de contenido
