Tabla de contenido
1. Safety Instructions
For skilled electricians and instructed
personnel in accordance with national
regulation, including the relevant standard and,
where applicable, in acc.with IEC 60079-17 on
electrical apparatus for explosive atmospheres.
¡The luminaires must not be operated in
Zones 0 and 20!
¡The tecnical data indicated on the
luminaires are to be observed!
¡Changes of the design and modifications to
the luminaires are not permitted!
¡The luminaires shall be operated as
intended and only in undamaged and
perfect conditions!
Cooper Cr
Cooper Cr
¡Only genuine Cooper Cr
Cooper Crouse-Hinds, S.A.
Cooper Cr
spare parts may be used for replacement!
¡Repairs that affect the explosion protection,
may only be carried out by
Cooper Crouse-Hinds, S.A.
Cooper Cr
Cooper Cr
Cooper Cr
Cooper Cr
ouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A. or a qualified
ouse-Hinds, S.A.
"electrician" and will subsequenctly have to
be cheked by an "expert"!
Do not keep these operating instructions
inside the luminaire during opertion.
¡The national safety rules and
regulations for prevention of accidents
and the following safety instructions
which are marked with an (
operting instructions, will have to be
observed!
2. Conformity with standards
This explosion protected luminaires meets the
requeriments of IEC/EN 60079-1, IEC/EN 60079-7,
IEC/EN 61241-1 and EN60598. It also complies with
the EC Directives for "Apparatus and protective
systems for use in explosive atmospheres" (94/9/EC).
It has been designed, manufactured and tested in
accordance to the state of the art and according to
EN29001 (ISO9001).
The luminaire are suitables for use in explosive
atmospheres, Zone 1 and 2 acc. to IEC60079-10 and
Zones 21 and 22 acc. IEC 61241-10.
3. Technical data
Application
II2GD
Class I
Exd/de T
Class II
Ex tD A21 IP66 T
Certificacions
LOM 02 ATEX2018X
IECEX - BKI 07.0032X
Others, contact us
Serie of types:
See Table 1
Lamps to be use
3)
:
Lamps with lampholder
E27 acc. EN60061-1
Approval of the production
ATEX Quality assurance: LOM 02 ATEX 9040
Degree of protection
acc. EN60598:
IP 66
Insulation class
acc. EN60598:
I
Temperature of use:
- 50
o
C to + 55
≤ 250V
Rated voltage
Material of enclosure:
Metal aloy aluminium
without Cu,
painted polyester grey.
Notes:
2) Special conditions for safe use of luminaires with direct entry.
The cable of the main connection will be adecuated for a temperature in confinuos service,follow indicated.:
Lamps 100W
for Tamb –20
C / + 40
C, Tw cable > 105
o
o
Lamps 60W and 70W
for Tamb –20
o
C / + 40
o
C, Tw cable > 100
3) See table 2, thermal class acc. the lamp used.
4) Non included.
Material of glas
Storage temperature in original
Packing
Terminals capacity:
Entries of cables
Direct entry:
Indirect entry:
Dimensions:
4. Installation
¡The respective national regulations as well
as the general rules of engineering which
apply to the installation and operation of explosi-
on protected apparatus will have to be observed!
¡Transport and storage of the luminaire is
permitted in original packaging only!
¡Pay attentionwhen mounting or repairing the
luminaire, dont damage the fire-finish of the glass
adquired during moulding (abrasions, sanding,
etc.) that can weaking their mechanical functions.
repairing the luminaire, dont damage the fire-
ouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
finish of the glass adquired during moulding
(abrasions, sanding, etc.) that can weaking their
mechanical functions!
Opening and closing the luminaires
¡The opening of luminaire always shall be
without voltage!
¡The luminaire is well closed when the glass-collar
and covers are completly threaded on the luminair
enclosure.
Dimensions for mounting:
Accesories for mounting:
See Cooper Cr
Cooper Cr
Cooper Cr
Cooper Cr
Cooper Crouse-Hinds, S.A.
) in theses
Cable entries
Mounting the selected cable entries
(cableglands or seals acc. needs) acc. type
and dimensions of the main conection cable,
following their manufacturer instructions.
The cable entries devices has to be the same
protection mode than the enclosure where they
are mounting.
Unused cabe entries have to be closed by a
correspondante certifyed blanking plug.
If the original blanking plugs are used , these
must be tightened with 15 Nm torque.
Main conection:
Lamps mounting
¡Only must be mounting apropiated lamps for
the supplied luminaire. See insications in the
general label of the luminaire!
3)
3)
2)
2)
5.
Taking into operation
¡Prior to operation check the luminaire for
its proper funtioning and installation in
compliance with these operting
instructions and others
applicable regulations!
Only carry out insulation measurements between PE
and external conductor L1 (L1, L2, L3) as well as
between PE and N.
-
measurement voltage: max. 1kV AC/DC
o
C
-
min. insulation: 2 M
Then the luminaire have to be tightly closed.
C ; para Tamb –20
C / + 55
o
o
o
C ; para Tamb –20
o
C / + 55
Borosilicate
-40
o
C a + 60
o
C
See wiring diagram
2 x ¾" ISO 7/1,
one plugged
2 x M25 x 1,5ISO9651,
one plugged
See figure 3.
See figue 3
ouse-Hinds, S.A.
ouse-Hinds, S.A. catalogue.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
See wiring diagram.
Ω
C, Tw cable > 120
C
o
o
o
C, Tw cable > 115
o
C
6.
Maintenance
¡Observe the national rules applicable to
maintenance, servicing, inspection and
repairing of apparatus for explosive atmospheres,
as well as the general rules of engineering!
¡For dust explosive appication, pay special
attention d'ont have present dust layers abore
5mm on side of the apparatus!
Servicing
The responsable of the safe use of these
apparatus is the property.
When servicing, in particular those components that
affect the explosion protection , will have to cheked,
e.g.:
Housing and glass for any cracks or damage.
The flameproof joint have to be clean,
undameged, without corrosion and perfect
greassed.
Gaskets for their perfect conditions.
Cable entries whitout corrosion.
Terminlas and blanking plugs for their firm fit.
Lamp replacement in acc. with the manufacturer
instructions.
Type of lamps used in acc. with the luminaire
specifications.
¡The flameproof of these apparatus have to
be greassed permanentlly in order to ensure
it protection in front of the corrosion, water
ingrees and seize-up problems. Cleaning rest of
greasse and corrosion no using sharp metallic
devices who can damage the surface of the joint,
and greasing they using apropiate greasse
therminally and chemically stable i.e.: Molikote
BR2plus.
¡When the housing need to be repeinted, pay
attention that the flameproof joints rest without
traks coating!
Inspection
¡The nationals regulations have to be
observed!
I.e. in Spain the inspections of the installations in
hazardous areas, have to be done by "qualified"
personnel in accordance with the Electrotechnical
Low Votage Regulation following the indications
stablished in IEC 60079-17.
¡When the inspections are in degree of
"Detailled" or "Closed", the luminaires have
to be disconnected from the main conection!
Repairing
¡The nationals regulations have to be
observed. The tasks of repairing have to be
made by "qualified" personnel!
¡The reparation of the sealed part between the
collarand the glass have to be done by
Cooper Cr
Cooper Cr
Cooper Cr
Cooper Crouse-Hinds, S.A.
Cooper Cr
ouse-Hinds, S.A.
ouse-Hinds, S.A.. The users are not
ouse-Hinds, S.A.
ouse-Hinds, S.A.
authorized to repair this sealed part.
All reparations have to be done without voltage!
For repair electrical equipments in protection mode is
suggested follow the instructions indicated
in IEC 79-19.
¡Only use genuine Cooper Cr
Cooper Crouse-Hinds, S.A.
Cooper Cr
Cooper Cr
Cooper Cr
spare parts!
Subject to alteration or supplement of this product
without any advertisement before.
Cooper Crouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
ouse-Hinds, S.A.
5
Tabla de contenido
