Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EN
English (English)
Technical Data
Speed
Power
Model
1
2
[Hp]
[RPM]
[W]
max. pressure 6.3bar(90psi)
a
: Vibration level, k Uncertainty ; L
h
Declaration of noise and vibration statement (ISO 15744 and ISO 28927-1)
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared
values of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured
in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way
the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user. We, CHICAGO PNEUMATIC
TOOLS , cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk
assessment in a work place situation over which we have no control. This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
An EU guide to managing hand-arm vibration can be found at www. pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf. We
recommend a programme of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that management procedures can
be modified to help prevent future impairment.
Machine type(s)
• This product is designed for removing material using abrasives. No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
Operation
• Fix the accessories properly to the tool.
• Connect device as shown in Fig. 01.
• To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
After the work is finished
WARNING ! The stopping time may be longer than 5 seconds.
• Make sure that the tool is switched off and has come to a complete stop before it is laid down.
• The stopping time is dependent on the abrasive used.
• Put down the tool carefully, so that there is no risk that the tool start by itself.
Lubrication
• Use an air line lubricator with SAE #10 oil, adjusted to two (2) drops per minute.
Maintenance instruction
• Follow local country environmental regulations for safe handling and disposal of all components.
• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised
dealer for advice on technical service or if you require spare parts.
• Always ensure that the machine is disconnected from energy source to avoid accidental operation.
• Disassemble and inspect the tool every three 3 months (500 hours) if the tool is used every day. Replace damaged or worn parts.
Overspeed air shut-off device
• Be particularly careful with the speed governor and the overspeed air shut-off device. Careless maintenance or treatment may prevent them from functioning
correctly. If the machine stops suddenly or does not reach rated speed when connected to the air supply, the overspeed shut-off device may have closed the
inlet air.
• The machine must imperatively be dismantled and checked before resetting the overspeed shut-off device.
Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
ANSI Standard
The CP3330 SALAVET, CP3330 SALAVAD, CP3330 SALAVEL, CP3340 SALAVET, CP3340 SALAVAD, CP3340 SALAVEL models are in conformity with the
requirements of American National Sandard ANSI B7.1-2010.
EU Declaration of Conformity
We :
CHICAGO PNEUMATIC Tool Co. LLC ,1815 Clubhouse Road, Rock Hill, SC 29730 - USA
Machine type(s):
Vertical Grinder
Declare under our sole responsibility that the product(s): CP3330 SALAVET, CP3330 SALAVADE, CP3330 SALAVELE, CP3340 SALAVET, CP3340 SALA-
VADE & CP3340 SALAVELE
00001 - 99999
Serial Number:
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery"
(17/05/2006)
applicable harmonised standard(s) : EN ISO 11148-7:2012
Name and position of issuer :
Place & Date :
Saint-Herblain, 16/01/2020
Technical file available from EU headquarter. Pascal Roussy, R&D manager, CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Spindle
Air Consumption
Wheel
Thread
at load
3
4
[l/min]
/
[SCFM]
Sound pressure dB(A), K
pA
Origin of the product : Taiwan
PASCAL ROUSSY (R&D Manager)
Weight
Air Inlet
5
6
7
[kg] / [lb]
[inch]
= K
= 3 dB Uncertainty.
pA
WA
CP3330 & CP3340
Sound pressure
Inner Hose Dia.
L
pA
8
9
[inch]
[dB(A)]
[mm]
Grinder
Vibrations
Sound power
L
a
K
wA
hd
10
11
12
[dB(A)]
[m/s²]
[m/s²]
2006/42/EC
Tabla de contenido
