WALMEC GENESI CARBONIO 360 HTE Clear Manual De Instrucciones página 20

Mod. GENESI CARBONIO 360 HVLP
TECHNICAL SPECIFICATIONS
- Air fitting: G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
ø ** PRODUCT LOAD (3.5 turns)
FEED
0.8
Gravity
1.0
Gravity
1.2
Gravity
1.3
Gravity
1.4
Gravity
1.5
Gravity
1.7
Gravity
1.9
Gravity
2.5
Gravity
** Product flow was calculated with water, setting the recommended regulations.
RECOMMENDED AIR PRESSURE DURING USE: 2 bar (29 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer efficiency
must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0,7 bar (10 psi).
USE
The GENESI CARBONIO 360 HVLP series of spray guns has been designed for the application of colours, paints or other fluid
substances.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a
Walcom FSRD3/4 filter unit or the most complete and efficient Walcom TD3 PRO multifunction heat conditioner).
ADVICE FOR CORRECT USE
1. The distance between the spray gun and the surface to be painted must be set between 100 e i 150 mm (3,9"- 5,9").
If the spray gun is working at a too low pressure and at a too high distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the
surface being painted and the paint must be applied in horizontal
strokes. Any eventual shift from this position when spraying will
result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Ford
cup n°4. These values depend on the application and the nozzle
size used.
SHAPE OF THE FAN
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
Adjust the air pressure, product quantity and spray opening
until obtaining a regular imprint as in fig. C
istruzioni WI34_18.indd 20
101Gr/min. (3.5 oz/min.)
142 Gr/min. (5.0 oz/min.)
221 Gr/min. (7.8 oz/min.)
239 Gr/min. (8.4 oz/min.)
263 Gr/min. (9.3 oz/min.)
275 Gr/min. (9.7 oz/min.)
289 Gr/min. (10.2 oz/min.)
354 Gr/min. (12.5 oz/min.)
420 Gr/min. (15.6 oz/min.)
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
20
ADJUSTMENTS
- Working pressure: 1,5-2,0 bar (22-29 psi)
- Fan: Fully open
- Product: 3,5-5 turns
FAN DIMENSIONS AT 15 cm (5.9")
14 cm (5.6")
16 cm (6.3")
22 cm (8.7")
23 cm (9.1")
24 cm (9.5")
26 cm (10.3")
27 cm (10.6")
30 cm (11.8")
30 cm (11.8")
AIR CONSUMPTION
360 l/min (12.7 CFM)
- Regular jet
09/01/18 14.18
Mod.
TECH
- Air fittin
- Maximu
ø
0.7
G
1.0
G
1.2
G
1.3
G
1.4
G
1.5
G
1.7
G
1.9
G
** Produ
At the rec
USE
Spray gu
sectors r
The instr
To obtain
1. When
2. Make
Walcom
ADVI
1.The dis
If the spr
2. The je
surface b
strokes.
result in
3. Correc
cup n°4.
size used
SHAP
Adjust t
opening