Technical Specifications - WALMEC GENESI CARBONIO 360 HTE Clear Manual De Instrucciones

Mod. GENESI CARBONIO 360 HTE CLEAR

TECHNICAL SPECIFICATIONS

- Air fitting: G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
** PRODUCT LOAD (3.5 turns)
ø FEED
1.1
Gravity
1.2
Gravity
1.3 Gravity
1.4
Gravity
1.7 Gravity
1.9 Gravity
2.5 Gravity
** Product flow was calculated with water, setting the recommended regulations.
At the recommended air pressure the spray gun works with at transfer efficiency superior to 65%.
USE
The GENESI CARBONIO 360 HTE Clear series of spray guns has been designed for the application of colours, paints or other
fluid substances.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a
Walcom FSRD3/4 filter unit or the most complete and efficient Walcom TD3 PRO multifunction heat conditioner).
ADVICE FOR CORRECT USE
1. The distance between the spray gun and the surface to be painted must be set between 150 and 200 mm (5.9 - 7.9").
If the spray gun is working at a too low pressure and at a too high distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the
surface being painted and the paint must be applied in horizontal
strokes. Any eventual shift from this position when spraying will
result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Ford
cup n°4. These values depend on the application and the nozzle
size used.
SHAPE OF THE FAN
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
Adjust the air pressure, product quantity and spray opening
until obtaining a regular imprint as in fig. C
istruzioni WI34_18.indd 18
211 Gr/min. (7.4 oz/min.)
249 Gr/min. (8.8 oz/min.)
254 Gr/min. (9.0 oz/min.)
300 Gr/min. (10.6 oz/min.)
358 Gr/min. (12.6 oz/min.)
380 Gr/min. (13.4 oz/min.)
450 Gr/min. (16.4 oz/min.)
RECOMMENDED AIR PRESSURE: 2 bar (29 psi)
18
ADJUSTMENTS
- Working pressure: 1,5-2,5 bar (22-36 psi)
- Fan: Fully open
- Product: 3,5-5 turns
FAN DIMENSIONS AT 20 cm (7.9")
29 cm (11.4")
31 cm (12.2")
33 cm (13.0")
32 cm (8.3")
35 cm (13.8")
36 cm (14.2")
36 cm (14.2")
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
AIR CONSUMPTION AT 0.7 bar
(10 psi) CAPTEST
380 l/min (13.4 CFM)
- Regular jet
09/01/18 14.18
Mod.
TECH
- Air fittin
- Maximu
ø
0.8
1.0
1.2
1.3
1.4
1.7
1.9
2.5
** Produ
USE
The GEN
fluid sub
The instr
To obtain
The instr
1. When
2. Make
Walcom
ADVI
1. The di
If the spr
2. The je
surface b
strokes.
result in
3. Correc
cup n°4.
size used
SHAP
Adjust t
until ob