HQ-Power THARAS VPATR200 Manual Del Usuario página 4

5. Ove erview and
Refer to t the illustration o
1a Att enuation knob f
1b foll owing LCD (dep
sho own):
2a Pro otection, clip, sig
2b
3 LCD D.
4 On/ /off switch.
5 Pre ess the load butt
®
6 Spe eakon speaker
mu ust be 4 Ω. Use
fro m 1.5 mm² or l
loss s. The signal pa
mix xer/preamp out
out tput > speaker
®
7 Spe eakon mono sp
8 Ω Ω. Use good qua
1.5 5 mm² or larger The e signal path sh
mix xer/preamp out
out tput > speaker
®
8 Spe eakon speaker
mu ust be 4 Ω. Use
fro m 1.5 mm² or l
loss s. The signal pa
mix xer/preamp out
out tput > speaker
9 Bal anced XLR sign
10 Bal anced XLR sign
11 Unb balanced RCA s
12 Spe eaker binding p
can n present short-
be taken to ensure
13 Pow wer cord connec
14 Lim miter switch. Sw
15 Mo de selection sw
Ste ereo: The amplif
Brid dged mono: The
power speaker
speaker outpu
lowest setting
16 Gro ound lift switch.
sig nal ground and
17 Air ventilation slot
07.05.201 0
VPATR200/V
use
on page 2 of th is manual.
for channel A/ch hannel B. Turnin
pending on swit ch setting, Brid
gnal and bridge LEDs for chann
ton to select the e output impeda
r output for cha nnel B. Use 1+1
good quality ca bles of the corr
arger cable. Ke ep the connecti
ath should be: s source output >
put > power am mplifier input (sh
input (unshielde ed speaker cabl
peaker output. Use 1+1- termi
ality cables of th he correct type.
r cable. Keep the e connection ca ould be: source e output > mixe
put > power am mplifier input (sh
input (unshielde ed speaker cabl
r output for cha nnel A. Use 1+1
good quality ca bles of the corr
arger cable. Ke ep the connecti
ath should be: s source output >
put > power am mplifier input (sh
input (unshielde ed speaker cabl
al output.
al input.
ignal inputs.
ost terminals. A As with all speak
-circuit to the am mplifier. Speake
e no bare wires can be touched
ction with fuse. Only replace th
witch on the limit ter to prevent in
itch. Select eith her the stereo (S
fier will operate e as two indepen
e amplifier will w work as one cha
rs. The bridged mode must be
t. Only one sing gle signal input
and use channe el A to control t
Some connecte ed equipment m
reduce the effe ect of the mains
s.
VPATR400
ng this knob wil ll show
ge or Stereo is
nel A/channel B. .
ance (4 Ω or 8 Ω Ω).
1- terminals onl ly. Minimum spe
ect type. Speak ker cables shoul
on cables as sh ort as possible
mixer/preamp input (shielded
hielded signal ca able), power am
e).
nals only. Minim mum speaker im
Speaker cables s should be man
bles as short as s possible to mi er/preamp input t (shielded signa
hielded signal ca able), power am
e).
1- terminals onl ly. Minimum spe
ect type. Speak ker cables shoul
on cables as sh ort as possible
mixer/preamp input (shielded
hielded signal ca able), power am
e).
ker wiring, care must be taken
er wires carry h igh voltages. Th
d as this may re sult in an electr
he fuse with a fu use of the same
nput signal surg ges to harm the
ST) or bridged m mono (BRI) mod
ndent channels, namely channe
annel. This is th he ideal mode w
used in conjunc ction with the M
is required (cha annel A). Turn c
he amplifier.
may present hum m. This switch w
s hum.
4
Re v. 01
eaker impedanc ce
d be manufactu ured
to minimize sig nal
signal cable),
mplifier
mpedance must be
nufactured from m
nimize signal lo ss. al cable),
mplifier
eaker impedanc ce
d be manufactu ured
to minimize sig nal
signal cable),
mplifier
to ensure no w wires
herefore, care s hould
ric shock.
rating.
amplifier.
de.
els A and B.
when using high- -
MONO BRIDGE [ 7]
channel B to the e
will remove the
©Vellema an nv