Rules Of Use; Preparing For Use - Active H24 Manual De Instrucciones

GB
ENGLISH
WARNING: Carefully read the safety precautions before
using the hedgetrimmer.
- Wear appropriate safety articles according with the local
regulations and the safety regulations enacted by the
professional associations, see paragraph "SAFETY
PRECAUTIONS"
- If you have not used the machine before, spend some time in
becoming familiar with the usage before operating.
- Work calmly and concentrated, only under good visibility
conditions and with care.
- It is forbidden to work on ladders, branches or from other
unsteady situations.
- Check the machine carefully before using it, make sure that there
are no loosened screws, damaged parts or fuel leakages.
- Check the condition of the antivibration components on a regular
basis. Avoid using the hedgetrimmer over excessively long
periods of time, excessive amounts of vibration can be harmful.
Remove from the working area grit, debris, ropes, metal parts or
any other objects which might get entangled around the blades.
The machine must be held by the operator standing on the
FUEL
WARNING. The machine is equipped with a two stroke engine.
Always run the machine with fuel, which is mixed with oil. Only
prepare the quantity of fuel for each job. Do not smoke. Refill
when the engine is switched off and away from a naked flame.
AIways use a minimum octane number of 90.
Mix fresh gasoline and ACTIVE oil in the ratio of 50:1 (2%). If the
ACTIVE oil is not available use a good 2 stroke oil quality in the
ratio of 25:1 (4%) see fig.15.
Important: always shake this fuel mix vigorously each time you
use it. Fuel mix properties deteriorate with time we therefore
recommend that you only make the quantity of fuel mix you will
need for each usage. Do not use fuel mix more than a week old
as this could damage the engine. Fill the brushcutter fuel tank
only to 3/4 capacity to allow for fuel expansion.
FUELING
WARNING: always shut off the engine before refueling. Slowly
open the cap of the fuel tank, when filling up with fuel, so that
possible over pressure disappears. Tighten the fuel cap carefully
after fuelling. Always move the machine at least 3 m (10Ft) from
the fueling area before starting. Before fueling clean the tank
cap area carefully, to ensure that no dirt falls into the tank make
sure that the fuel is well mixed by shaking the container before
fueling.

5. RULES OF USE

carburettor side and be used as in the picture fig.16.
- Remove the blades guard (1) fig.1 - The blades must not touch
the ground or any object.
THROTTLE/HANDLE fig.11
For ease of handling and to improve the cutting performance the
ACTIVE hedge trimmer is equipped with five position rotating
handle from 0° to 90°.
To adjust the rotating handle:
- Stop the engine
- Pull the lever (4 Fig. 8), see the arrow, in order unlock the handle
- Turn right or left (according to the cutting angle) till the handle is
locked.
EXAMPLES TO OPERATE THE HEDGE TRIMMER
Warning: Before operating make sure there are no objects on
the hedge that could damage the hedgetrimmer.
- Set the throttle lever at half position and start to cut the hedge.
- Start to cut step by step in order to avoid damage to the hedge
or damage to the hedgetrimmer on the bigger branches.

6. PREPARING FOR USE

STARTING
Lay the machine on a flat, bare surface and make sure that the
cutting tool is free.
WARNING:do not start the engine on your leg or knee.
Move ignition switch to (1). Fig.8
Push primer bulb (2) repeatedly 5 to 6 times.Fig.7
Move choke lever (1) to choke position (A) Fig.7.
Holding the unit down pull the starting handle until engine
attempts to run then move the choke lever (1) to open position
(B) Fig. 7.
Pull starter until engine runs.
Once the engine has started, press the throttle trigger a little (2)
and let the engine run.
Warning once the engine is warmed up do not use the primer
bulb (2) and the choke (1) to start up again fig.7.
Do not release the starter handle in pulled out position, as this
may damage the starting ass'y.
STOPPING ENGINE
Set the throttle lever (2) Fig.8 to idle position and wait a few
seconds to let the engine cool off. Move the ignition switch to
"stop" position (0). Fig.8
WARNING: with the engine idling (2600 - 3000 rpm)
the cutting tool should not rotate.If the idle speed is too
high turn counterclockwise the screw (H) Fig.2
20